From RobertVandusen at cunet.carleton.ca  Mon Oct  3 11:38:18 2022
From: RobertVandusen at cunet.carleton.ca (Robert Vandusen)
Date: Mon, 3 Oct 2022 15:38:18 +0000
Subject: [labnetwork] MA6 mask aligner lamp housing removal
Message-ID: <YT2PR01MB976396EC52D9C7DAB9FF0D2E915B9@YT2PR01MB9763.CANPRD01.PROD.OUTLOOK.COM>

Hi all.
We have to replace a bad cardcage cooling fan in our Karl Suss MA6 mask aligner.
These fans are sandwiched above the cardcage and below the main lamp housing.
The lamp housing does appear to be on a sliding rail of some kind to either slide or flip out of the way to allow access,  but we are not quite sure how to move it.
The manual is of no help.   We are trying to figure it out but if anyone knows how to do this please let me know.

Thanks
Rob

Robert Vandusen
Technical Officer, Microfabrication Lab
Electronics Department
Carleton University
room: 4184 Mackenzie Building
613-520-2600<tel:613-520-2600> ext 5761
Robert_vandusen at cunet.carleton.ca<mailto:Robert_vandusen at cunet.carleton.ca>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221003/ef441218/attachment.html>

From codreanu at udel.edu  Tue Oct  4 10:32:54 2022
From: codreanu at udel.edu (Iulian Codreanu)
Date: Tue, 4 Oct 2022 10:32:54 -0400
Subject: [labnetwork] CDA pressure booster?
Message-ID: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>

Dear Lab Network,

The new ion mill I expect early next year requires 160 psig CDA, which 
is more than what my nominally 100 psig CDA system can provide.

I am writing to ask for advice on what the best approach for providing 
160 psig may be. I would like to avoid installing a compressor outside 
of the cleanroom and having to penetrate the cleanroom envelope.

Thank you very much,

Iulian

-- 
iulian Codreanu, Ph.D.
Director, Nanofabrication Facility
University of Delaware
Harker ISE Lab, Room 163
221 Academy Street
Newark, DE 19716
302-831-2784
http://udnf.udel.edu



From plenvik at ucsb.edu  Tue Oct  4 10:56:15 2022
From: plenvik at ucsb.edu (Peder Lenvik)
Date: Tue, 4 Oct 2022 07:56:15 -0700
Subject: [labnetwork] CDA pressure booster?
In-Reply-To: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>
References: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>
Message-ID: <17233adbb0ba0abc217a8a7a445bcca6@mail.gmail.com>

https://www.maxprotech.com/products/gas-boosters/

not sure of flow rates, etc. but something like this should work.




Peder

-----Original Message-----
From: labnetwork <labnetwork-bounces at mtl.mit.edu> On Behalf Of Iulian
Codreanu
Sent: Tuesday, October 4, 2022 7:33 AM
To: Fab Network <labnetwork at mtl.mit.edu>
Subject: [labnetwork] CDA pressure booster?

Dear Lab Network,

The new ion mill I expect early next year requires 160 psig CDA, which is
more than what my nominally 100 psig CDA system can provide.

I am writing to ask for advice on what the best approach for providing
160 psig may be. I would like to avoid installing a compressor outside of
the cleanroom and having to penetrate the cleanroom envelope.

Thank you very much,

Iulian

--
iulian Codreanu, Ph.D.
Director, Nanofabrication Facility
University of Delaware
Harker ISE Lab, Room 163
221 Academy Street
Newark, DE 19716
302-831-2784
http://udnf.udel.edu


_______________________________________________
labnetwork mailing list
labnetwork at mtl.mit.edu
https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork


From lvchang at Central.UH.EDU  Tue Oct  4 10:58:24 2022
From: lvchang at Central.UH.EDU (Chang, Long)
Date: Tue, 4 Oct 2022 14:58:24 +0000
Subject: [labnetwork] CDA pressure booster?
In-Reply-To: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>
References: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>
Message-ID: <FA31F8C2-F8E6-47AA-B563-24559973EF8A@central.uh.edu>

We use a nitrogen booster, see attached. The booster is powered by facility nitrogen at 70 psi and automatically keeps a reservoir cylinder at 1,500 psi. We tap that cylinder for 90psi and 500 psi to run our Nanoimprinter.

[cid:F443BF5E-FD0D-4ADE-9340-BE1D7CBB59B9]
On Oct 4, 2022, at 9:32 AM, Iulian Codreanu <codreanu at udel.edu<mailto:codreanu at udel.edu>> wrote:

Dear Lab Network,

The new ion mill I expect early next year requires 160 psig CDA, which is more than what my nominally 100 psig CDA system can provide.

I am writing to ask for advice on what the best approach for providing 160 psig may be. I would like to avoid installing a compressor outside of the cleanroom and having to penetrate the cleanroom envelope.

Thank you very much,

Iulian

--
iulian Codreanu, Ph.D.
Director, Nanofabrication Facility
University of Delaware
Harker ISE Lab, Room 163
221 Academy Street
Newark, DE 19716
302-831-2784
https://urldefense.com/v3/__http://udnf.udel.edu__;!!LkSTlj0I!CGo6WvreHfIvidUWGDgQ_Ud-XdcdkIHoRtorxMUGRVETt1WuDY9fdN9ncRORjXx9OP7qkOANXM_5MjyJTAWRl1o$

_______________________________________________
labnetwork mailing list
labnetwork at mtl.mit.edu<mailto:labnetwork at mtl.mit.edu>
https://urldefense.com/v3/__https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork__;!!LkSTlj0I!CGo6WvreHfIvidUWGDgQ_Ud-XdcdkIHoRtorxMUGRVETt1WuDY9fdN9ncRORjXx9OP7qkOANXM_5MjyJVzWCpAI$

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221004/b06b9953/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Screen Shot 2022-10-04 at 9.53.56 AM.png
Type: image/png
Size: 9206970 bytes
Desc: Screen Shot 2022-10-04 at 9.53.56 AM.png
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221004/b06b9953/attachment.png>

From spaolini at cns.fas.harvard.edu  Tue Oct  4 12:04:05 2022
From: spaolini at cns.fas.harvard.edu (Paolini, Steven)
Date: Tue, 4 Oct 2022 16:04:05 +0000
Subject: [labnetwork] CDA pressure booster?
In-Reply-To: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>
References: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>
Message-ID: <BL0PR07MB4050486133A9F539CE19160BDF5A9@BL0PR07MB4050.namprd07.prod.outlook.com>

Iulian,
  I have an IBE with the same requirements. The volume of high pressure N2 or air is small since it is used only to drive a piston for opening the chuck clamp. We simply use a regulator with a 0-400 PSI output for this purpose. The cylinder lasts for months depending on use.
  Equipment Dood.

Steve Paolini
Principal Equipment Engineer
Harvard University Center for Nanoscale Systems
11 Oxford St.
Cambridge, MA 02138
617- 496- 9816
spaolini at cns.fas.harvard.edu
www.cns.fas.harvard.edu

-----Original Message-----
From: labnetwork <labnetwork-bounces at mtl.mit.edu> On Behalf Of Iulian Codreanu
Sent: Tuesday, October 04, 2022 10:33 AM
To: Fab Network <labnetwork at mtl.mit.edu>
Subject: [labnetwork] CDA pressure booster?

Dear Lab Network,

The new ion mill I expect early next year requires 160 psig CDA, which is more than what my nominally 100 psig CDA system can provide.

I am writing to ask for advice on what the best approach for providing
160 psig may be. I would like to avoid installing a compressor outside of the cleanroom and having to penetrate the cleanroom envelope.

Thank you very much,

Iulian

--
iulian Codreanu, Ph.D.
Director, Nanofabrication Facility
University of Delaware
Harker ISE Lab, Room 163
221 Academy Street
Newark, DE 19716
302-831-2784
http://udnf.udel.edu


_______________________________________________
labnetwork mailing list
labnetwork at mtl.mit.edu
https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork


From jtmitch5 at ncsu.edu  Tue Oct  4 11:54:16 2022
From: jtmitch5 at ncsu.edu (James Mitchell)
Date: Tue, 4 Oct 2022 11:54:16 -0400
Subject: [labnetwork] CDA pressure booster?
In-Reply-To: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>
References: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>
Message-ID: <CAEXS_M_e7BdSjOpsPTpZx8iD_Sq1cNRuv40+j-4BtOi-p8aJ-A@mail.gmail.com>

It may be better and cheaper to use a 300 size cylinder with air or low
purity N2.
Attach a 580 CGA regulator and you are good to go.
These bottles would be cleaner than a compressor and only cost about $15 a
bottle.
If you need more volume, an LN2 dewar could also work.

Jim

On Tue, Oct 4, 2022 at 10:41 AM Iulian Codreanu <codreanu at udel.edu> wrote:

> Dear Lab Network,
>
> The new ion mill I expect early next year requires 160 psig CDA, which
> is more than what my nominally 100 psig CDA system can provide.
>
> I am writing to ask for advice on what the best approach for providing
> 160 psig may be. I would like to avoid installing a compressor outside
> of the cleanroom and having to penetrate the cleanroom envelope.
>
> Thank you very much,
>
> Iulian
>
> --
> iulian Codreanu, Ph.D.
> Director, Nanofabrication Facility
> University of Delaware
> Harker ISE Lab, Room 163
> 221 Academy Street
> Newark, DE 19716
> 302-831-2784
> http://udnf.udel.edu
>
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>


-- 
*Thank you, Jim*

*James Mitchell*
*Specialty Trades Technician*
*Dept. of Electrical and Computer Engineering*
*North Carolina State University Nanofabrication Facility (NNF)*
*MRC RM243A **Box 7911*
*2410 Campus Shore Dr., Raleigh, NC 27606*
*jtmitch5 at ncsu.edu* <jtmitch5 at ncsu.edu>
*Desk: 919-515-5394*
*Cell: 919-717-7325*
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221004/dbb005b4/attachment.html>

From dwolff at nelhydrogen.com  Tue Oct  4 12:43:44 2022
From: dwolff at nelhydrogen.com (David Wolff)
Date: Tue, 4 Oct 2022 16:43:44 +0000
Subject: [labnetwork] CDA pressure booster?
In-Reply-To: <17233adbb0ba0abc217a8a7a445bcca6@mail.gmail.com>
References: <14d66647-fa70-6c58-09dd-181b74c492de@udel.edu>
 <17233adbb0ba0abc217a8a7a445bcca6@mail.gmail.com>
Message-ID: <BL0PR08MB4593BF4E42E6C5E03B066D44C65A9@BL0PR08MB4593.namprd08.prod.outlook.com>

The indicated equipment is what?s called a pneumatic intensifier. They?re available from a number of suppliers including Haskell.  Check and make sure that it?s suitable for continuous use. I?m not sure.

Dave Wolff.  Nel Hydrogen.  860.604.3282
Via cell phone - pls excuse spelling errors
________________________________
From: labnetwork <labnetwork-bounces at mtl.mit.edu> on behalf of Peder Lenvik <plenvik at ucsb.edu>
Sent: Tuesday, October 4, 2022 10:56:15 AM
To: Iulian Codreanu <codreanu at udel.edu>; Fab Network <labnetwork at mtl.mit.edu>
Subject: Re: [labnetwork] CDA pressure booster?

CAUTION: Our automatic validation of the sender of this mail failed. Pay extra attention to attachments as well as links!!

https://nam10.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.maxprotech.com%2Fproducts%2Fgas-boosters%2F&amp;data=05%7C01%7Cdwolff%40nelhydrogen.com%7C351f274d061b451a7e0f08daa62171e6%7C76311e5d2c31404ea148a4c38d285e9e%7C0%7C0%7C638004959843659194%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&amp;sdata=y1HNLKfLeqioGl%2BWrNJOukNZ%2BYqVKsnyjn60XDtS6uc%3D&amp;reserved=0

not sure of flow rates, etc. but something like this should work.




Peder

-----Original Message-----
From: labnetwork <labnetwork-bounces at mtl.mit.edu> On Behalf Of Iulian
Codreanu
Sent: Tuesday, October 4, 2022 7:33 AM
To: Fab Network <labnetwork at mtl.mit.edu>
Subject: [labnetwork] CDA pressure booster?

Dear Lab Network,

The new ion mill I expect early next year requires 160 psig CDA, which is
more than what my nominally 100 psig CDA system can provide.

I am writing to ask for advice on what the best approach for providing
160 psig may be. I would like to avoid installing a compressor outside of
the cleanroom and having to penetrate the cleanroom envelope.

Thank you very much,

Iulian

--
iulian Codreanu, Ph.D.
Director, Nanofabrication Facility
University of Delaware
Harker ISE Lab, Room 163
221 Academy Street
Newark, DE 19716
302-831-2784
https://nam10.safelinks.protection.outlook.com/?url=http%3A%2F%2Fudnf.udel.edu%2F&amp;data=05%7C01%7Cdwolff%40nelhydrogen.com%7C351f274d061b451a7e0f08daa62171e6%7C76311e5d2c31404ea148a4c38d285e9e%7C0%7C0%7C638004959843659194%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&amp;sdata=GyOzz%2FUQd7B6prRk1uVJTQnnoMe7MacQ1RGH3PUczlw%3D&amp;reserved=0


_______________________________________________
labnetwork mailing list
labnetwork at mtl.mit.edu
https://nam10.safelinks.protection.outlook.com/?url=https%3A%2F%2Fmtl.mit.edu%2Fmailman%2Flistinfo.cgi%2Flabnetwork&amp;data=05%7C01%7Cdwolff%40nelhydrogen.com%7C351f274d061b451a7e0f08daa62171e6%7C76311e5d2c31404ea148a4c38d285e9e%7C0%7C0%7C638004959843659194%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&amp;sdata=bF60F3HbM7As3GXie1AMl5UiM%2F%2Fd3hdcrBWd4cTfO14%3D&amp;reserved=0

_______________________________________________
labnetwork mailing list
labnetwork at mtl.mit.edu
https://nam10.safelinks.protection.outlook.com/?url=https%3A%2F%2Fmtl.mit.edu%2Fmailman%2Flistinfo.cgi%2Flabnetwork&amp;data=05%7C01%7Cdwolff%40nelhydrogen.com%7C351f274d061b451a7e0f08daa62171e6%7C76311e5d2c31404ea148a4c38d285e9e%7C0%7C0%7C638004959843659194%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&amp;sdata=bF60F3HbM7As3GXie1AMl5UiM%2F%2Fd3hdcrBWd4cTfO14%3D&amp;reserved=0
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221004/5d8563e1/attachment.html>

From wjkiethe at ncsu.edu  Tue Oct  4 14:20:42 2022
From: wjkiethe at ncsu.edu (William Kiether)
Date: Tue, 4 Oct 2022 14:20:42 -0400
Subject: [labnetwork] Request for BPSG service work
Message-ID: <CAN1vinuPXot5M8bbDKEzPbrBRFTXMUuBwgbfmpjEMp9JzEP4Vw@mail.gmail.com>

>From my boss

Hello --

We are looking for someone who can offer BPSG deposition, preferably via
PECVD.

Please email Phil Barletta (pbarlet at ncsu.edu) if you have this capability,
or know of someone that does.

Thank you,
Phil


--

*Dr. Philip Barletta*
Director of Operations, NC State Nanofabrication Facility
Affiliate Faculty, Department of Electrical and Computer Engineering
NC State University
pbarlet at ncsu.edu
919-513-1976
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221004/b2984302/attachment.html>

From olms0025 at umn.edu  Tue Oct  4 16:51:57 2022
From: olms0025 at umn.edu (Brian K. Olmsted)
Date: Tue, 4 Oct 2022 15:51:57 -0500
Subject: [labnetwork] Request for BPSG service work
In-Reply-To: <CAN1vinuPXot5M8bbDKEzPbrBRFTXMUuBwgbfmpjEMp9JzEP4Vw@mail.gmail.com>
References: <CAN1vinuPXot5M8bbDKEzPbrBRFTXMUuBwgbfmpjEMp9JzEP4Vw@mail.gmail.com>
Message-ID: <CAMNfp69q0MU0xtb2NAbb7J7Nbe5AZHsKCgM776b6e=RC0DbzZA@mail.gmail.com>

We can do this for you. Sent you a separate email.

Thanks,

Brian

On Tue, Oct 4, 2022 at 3:28 PM William Kiether <wjkiethe at ncsu.edu> wrote:

> From my boss
>
> Hello --
>
> We are looking for someone who can offer BPSG deposition, preferably via
> PECVD.
>
> Please email Phil Barletta (pbarlet at ncsu.edu) if you have this
> capability, or know of someone that does.
>
> Thank you,
> Phil
>
>
> --
>
> *Dr. Philip Barletta*
> Director of Operations, NC State Nanofabrication Facility
> Affiliate Faculty, Department of Electrical and Computer Engineering
> NC State University
> pbarlet at ncsu.edu
> 919-513-1976
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221004/6fda4f80/attachment.html>

From larry.hess-1 at nasa.gov  Wed Oct  5 13:28:38 2022
From: larry.hess-1 at nasa.gov (Hess, Larry A. (GSFC-5530))
Date: Wed, 5 Oct 2022 17:28:38 +0000
Subject: [labnetwork] Need for 6"wafer bonding
Message-ID: <SJ0PR09MB9318E6891F6E03537062C820FC5D9@SJ0PR09MB9318.namprd09.prod.outlook.com>

Hi,

NASA has a flight project in need of  6? wafer bonding capability. Our Suss SB-6e Bonder is currently down and the lead time is 6 months for the repair.
We are looking for a (preferably but not absolute) user facility within driving distance of the greater DC area with similar bonding capability.
The bonding material is Cyclotene 3022-35 which is a heat cured polymer and the conditions are 10hrs at 200?C with 3bar applied pressure. We prefer
the flat top plate arrangement with cut-outs to allow clamping during the process (the flat plate feature is more critical than the cut-outs for clamping).
If you have access to this capability or know of a facility with this capability please contact me. Thanks for your interest!


Larry Hess, PhD
NASA/Goddard Space Flight Center
Detector Systems Branch, Code 553
B11, R011
8800 Greenbelt Road
Greenbelt, MD 20771
Office: 301-286-0259
Mobile: 301-461-7585
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221005/88f352b5/attachment.html>

From levangie at mit.edu  Wed Oct  5 15:30:57 2022
From: levangie at mit.edu (Mackenzie LeVangie)
Date: Wed, 5 Oct 2022 19:30:57 +0000
Subject: [labnetwork] optical table free to gd home
In-Reply-To: <CDEA4B18-A082-4B87-8D83-EA0AA8FF068E@mit.edu>
References: <496819FD-5B91-422A-886E-90DE6FA50FEE@mit.edu>
 <CDEA4B18-A082-4B87-8D83-EA0AA8FF068E@mit.edu>
Message-ID: <deea38e09f5d4faf8746f2f0b75a702b@oc11expo31.exchange.mit.edu>

Hello!

This table is still available. Please let me know if you are interested. We are hoping to have it removed from our space before December. Thanks!

-Mackenzie LeVangie

From: Vicky Diadiuk <diadiuk at mit.edu>
Sent: Wednesday, September 28, 2022 4:10 PM
To: labnetwork at mtl.mit.edu
Cc: Mackenzie LeVangie <levangie at mit.edu>
Subject: optical table free to gd home

Hi,
 It?s not needed anymore & is available immediately.
If interested pls reply directly to MacKenzie at levangie at mit.edu<mailto:levangie at mit.edu>
Thx,
Vicky


8? x 4? and floatable



[IMG_1439.jpg]


[IMG_1440.jpg]




-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221005/09c4eadd/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 118976 bytes
Desc: image001.jpg
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221005/09c4eadd/attachment.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image002.jpg
Type: image/jpeg
Size: 105368 bytes
Desc: image002.jpg
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221005/09c4eadd/attachment-0001.jpg>

From lopezg at seas.upenn.edu  Thu Oct  6 12:47:36 2022
From: lopezg at seas.upenn.edu (Gerald Lopez)
Date: Thu, 6 Oct 2022 12:47:36 -0400
Subject: [labnetwork] UPenn 2022 Singh Center for Nanotechnology Annual User
 Meeting
Message-ID: <CAERBAG9VOx54SK2rakPbW8q_hJR2pEB6fapB6dvMHuD7Qc9HmA@mail.gmail.com>

Dear Colleagues:

You are cordially invited to attend the 2022 Singh Center for
Nanotechnology Annual User Meeting next *Thursday, October 13*, *2022, 9 am
- 5:15 pm EDT*. The meeting is free to attend and will feature research
talks spanning academia and industry with featured presentations from
select vendors. The event occurs in person in Philadelphia, Pennsylvania,
USA, at the University of Pennsylvania Singh Center for Nanotechnology. For
those that register and cannot attend in person, we will broadcast talks
over Zoom. Talks will not be recorded. Please feel free to take a look at our
program
<https://drive.google.com/file/d/1Rfo7AmYRn7fas5Fr6sVvJ-L-B7Mqfgns/preview>.

If you are interested in attending or want to know more, go to
singhnano.eventbrite.com. Those attending in person will be able to
participate in our vendor exhibition, meals/refreshments, poster session
and door prizes.

Again, if you can't attend in person, we will provide a Zoom link for all
our online attendees, but you'll need to register at
singhnano.eventbrite.com. Registration closes *on October 12*.

Sincerely,
Gerald-

Gerald G. Lopez, Ph.D. (he/him/his)

Director of Operations and Business Development & Center Associate Director

University of Pennsylvania | Singh Center for Nanotechnology

NNCI Mid-Atlantic Nanotechnology Hub (MANTH) ? nnci.net

3205 Walnut Street, Philadelphia PA 19104 USA

nano.upenn.edu ? lopezg at seas.upenn.edu ? +1-215-573-4041 ?
linkedin.com/in/geraldglopez/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221006/91140ba2/attachment.html>

From yaofootball at gmail.com  Thu Oct  6 13:10:32 2022
From: yaofootball at gmail.com (Football)
Date: Thu, 6 Oct 2022 12:10:32 -0500
Subject: [labnetwork] Cleanroom gloves
Message-ID: <CAOycKMZgLwJeNyVXGdsOmeMu3_Y8zT7YQY5oGuvyMEYEv3Xdjg@mail.gmail.com>

Dear Colleague,

I wonder what brands and types of cleanroom gloves you use in your
cleanroom. At Argonne, we have been using the *Kimberly-Clark
Professional? Kimtech? Pure G5 Blue Cleanroom Nitrile Gloves. *Some time
back we noticed that these blue ones were discontinued by the manufacturer,
then we started to use the *Kimberly-Clark Professional? Kimtech? Pure G3
Cleanroom NXT? Nitrile Gloves. *Besides the pros that this G3 type is less
expensive and releases less particles than the G5 blue ones, some users
noticed the difference in the grip strength of these two. The G3 has a
smooth finish while the G5 blue has a more coarse finish which some users
think has provided more grip strength.

Thanks!

*Fubo Rao, Ph.D.,*

*Nanofabrication Cleanroom Manager,*

*Center for Nanoscale Materials,*

*Argonne National Laboratory*

*9700 S. Cass Ave, Lemont, IL 60439*

*Phone: 630-252-5708*

*Email: frao at anl.gov <frao at anl.gov>*
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221006/b7ede9d9/attachment.html>

From ana.n.cohen.ctr at army.mil  Thu Oct  6 13:30:31 2022
From: ana.n.cohen.ctr at army.mil (Cohen, Ana N CTR USARMY DEVCOM ARL (USA))
Date: Thu, 6 Oct 2022 17:30:31 +0000
Subject: [labnetwork] MA6 mask aligner lamp housing removal
Message-ID: <BN8P111MB1447BCC04B15BE02CE92200D9F5C9@BN8P111MB1447.NAMP111.PROD.OUTLOOK.COM>


Hi Robert,

What generation is this? My Gen3 can slide the lamp back during the
initialization stage (it needs to be in the back position for the BA mode).
Alternatively I can manually press down on the spring holding it in
position, but that's less desirable. For access to electrical connections
everything typically requires removing a panel to actually access that area.

If you're looking for further MA6 support, it might be worth contacting Mark
Anderson (he's located in Vermont).

Kindly,
Ana

--
Ana N. Cohen [she/her/hers]
Photolithography Cleanroom Technician
General Technical Services, LLC | US Army Research Laboratory
2800 Powder Mill Road, Adelphi, MD 20783
Tel: 301-394-1527 | Email: ana.n.cohen.ctr at army.mil

-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/pkcs7-signature
Size: 6586 bytes
Desc: not available
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221006/8ee70e51/attachment.p7s>

From RobertVandusen at cunet.carleton.ca  Thu Oct  6 13:37:15 2022
From: RobertVandusen at cunet.carleton.ca (Robert Vandusen)
Date: Thu, 6 Oct 2022 17:37:15 +0000
Subject: [labnetwork] MA6 mask aligner lamp housing removal
In-Reply-To: <BN8P111MB1447BCC04B15BE02CE92200D9F5C9@BN8P111MB1447.NAMP111.PROD.OUTLOOK.COM>
References: <BN8P111MB1447BCC04B15BE02CE92200D9F5C9@BN8P111MB1447.NAMP111.PROD.OUTLOOK.COM>
Message-ID: <YT2PR01MB9763CD704297875A54009B19915C9@YT2PR01MB9763.CANPRD01.PROD.OUTLOOK.COM>

Thanks Ana.
We have an older MA6 with a fixed lamp housing.
We determined that the entire lamp housing would have to slide off the system to the right to get access to our cooling fans.
This would be a fairly difficult task.
We managed to get the fan blade re-attached to the existing motor and it is working for now.

Thanks for the contact information.
Best regards
Rob
Robert Vandusen
Technical Officer, Microfabrication Lab
Electronics Department
Carleton University
room: 4184 Mackenzie Building
613-520-2600?ext 5761
Robert_vandusen at cunet.carleton.ca



-----Original Message-----
From: Cohen, Ana N CTR USARMY DEVCOM ARL (USA) <ana.n.cohen.ctr at army.mil> 
Sent: October 6, 2022 1:31 PM
To: labnetwork at mtl.mit.edu; Robert Vandusen <RobertVandusen at cunet.carleton.ca>
Subject: Re: [labnetwork] MA6 mask aligner lamp housing removal


Hi Robert,

What generation is this? My Gen3 can slide the lamp back during the
initialization stage (it needs to be in the back position for the BA mode).
Alternatively I can manually press down on the spring holding it in
position, but that's less desirable. For access to electrical connections
everything typically requires removing a panel to actually access that area.

If you're looking for further MA6 support, it might be worth contacting Mark
Anderson (he's located in Vermont).

Kindly,
Ana

--
Ana N. Cohen [she/her/hers]
Photolithography Cleanroom Technician
General Technical Services, LLC | US Army Research Laboratory
2800 Powder Mill Road, Adelphi, MD 20783
Tel: 301-394-1527 | Email: ana.n.cohen.ctr at army.mil



From tony.olsen at utah.edu  Fri Oct  7 11:10:11 2022
From: tony.olsen at utah.edu (Tony L Olsen)
Date: Fri, 7 Oct 2022 15:10:11 +0000
Subject: [labnetwork] Cleanroom gloves
In-Reply-To: <CAOycKMZgLwJeNyVXGdsOmeMu3_Y8zT7YQY5oGuvyMEYEv3Xdjg@mail.gmail.com>
References: <CAOycKMZgLwJeNyVXGdsOmeMu3_Y8zT7YQY5oGuvyMEYEv3Xdjg@mail.gmail.com>
Message-ID: <BYAPR11MB3496E86D02931426A60403C5F15F9@BYAPR11MB3496.namprd11.prod.outlook.com>

There are lots of options, but for years we?ve been using TechNitrile TN2000 Series gloves (both white and blue) from TechNiGlove International.  Like most alternatives, they have microtextured fingertips, which are not visible to the naked eye, but we?ve been happy with them.  I don?t recall any complaints about grip.  They are available through various suppliers.

tonyO


Tony Olsen
Nanofab Cleanroom Supervisor/Process Engineer
University of Utah
36 S Wasatch Drive, Suite 2500
Salt Lake City, UT  84112
801-587-0651
www.nanofab.utah.edu



From: Football <yaofootball at gmail.com>
Sent: Thursday, October 6, 2022 11:11
To: labnetwork at mtl.mit.edu
Subject: [labnetwork] Cleanroom gloves

Dear Colleague,

I wonder what brands and types of cleanroom gloves you use in your cleanroom. At Argonne, we have been using the Kimberly-Clark Professional? Kimtech? Pure G5 Blue Cleanroom Nitrile Gloves. Some time back we noticed that these blue ones were discontinued by the manufacturer, then we started to use the Kimberly-Clark Professional? Kimtech? Pure G3 Cleanroom NXT? Nitrile Gloves. Besides the pros that this G3 type is less expensive and releases less particles than the G5 blue ones, some users noticed the difference in the grip strength of these two. The G3 has a smooth finish while the G5 blue has a more coarse finish which some users think has provided more grip strength.

Thanks!
Fubo Rao, Ph.D.,
Nanofabrication Cleanroom Manager,
Center for Nanoscale Materials,
Argonne National Laboratory
9700 S. Cass Ave, Lemont, IL 60439
Phone: 630-252-5708
Email: frao at anl.gov
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221007/b251d3b7/attachment.html>

From sergilendi at lsu.edu  Fri Oct  7 13:39:20 2022
From: sergilendi at lsu.edu (Sergi Lendinez)
Date: Fri, 7 Oct 2022 17:39:20 +0000
Subject: [labnetwork] Microfabrication class
Message-ID: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>

Dear labnetwork community,

Here at LSU we are planning to start a microfabrication class soon, and I would like to ask for your opinions about setting up this kind of class at a university. I am not sure if this topic has been discussed here before, so I apologize for any possible duplication.

Any information would be very helpful, like do's and don't's, devices being fabricated, number of students, students/teacher ratio, course load, etc.

I'd like to fabricate some CMOS device, but we lack some critical equipment such as a diffusion tube furnace, cvd, or packaging tools, so I'm looking for alternate ideas: maybe a photodiode/detector, a Hall sensor or some micro-fluidic channels. If anyone has some experience fabricating these devices in a class setup, is there anything you'd be willing to share?

Many thanks,
Sergi

---
Sergi Lendinez, Ph. D.
Assistant Director NFF | Louisiana State University
Center for Advanced Microstructures and Devices (CAMD)
6980 Hefferson Highway, Baton Rouge, LA 70803
(225) 578-9378
sergilendi at lsu.edu<mailto:sergilendi at lsu.edu> | lsu.edu/nanofabrication<https://lsu.edu/nanofabrication>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221007/4371f6c2/attachment.html>

From tatiana.pinedo at monash.edu  Sun Oct  9 22:29:53 2022
From: tatiana.pinedo at monash.edu (Tatiana Pinedo Rivera)
Date: Mon, 10 Oct 2022 13:29:53 +1100
Subject: [labnetwork] Cleanroom gloves
In-Reply-To: <BYAPR11MB3496E86D02931426A60403C5F15F9@BYAPR11MB3496.namprd11.prod.outlook.com>
References: <CAOycKMZgLwJeNyVXGdsOmeMu3_Y8zT7YQY5oGuvyMEYEv3Xdjg@mail.gmail.com>
 <BYAPR11MB3496E86D02931426A60403C5F15F9@BYAPR11MB3496.namprd11.prod.outlook.com>
Message-ID: <CABQu3YbGiHKe6qb-FtpFBfus+cKEQ=yUgOauXVS3H3vaP8cz_w@mail.gmail.com>

Hi colleagues,

In the spirit of sustainability, I know that Valutek has a line of
cleanroom-grade gloves for different cleanroom classes. They had a booth at
UGIM. They also do all sorts of cleanroom disposables: cleanroom wipes,
cleanroom paper they claim is recyclable, overshoes, hairnets, etc.
Valutek has recently partnered with Terra Cycle to offer a recycling program
<https://www.valutek.com/pages/recycling-program> and offer incentives to
recycle waste.
We haven't tried them yet. Is anyone currently using Valutek consumables
and their recycling program? I would be very keen to hear feedback about
their products and their recycling program.

Cheers,

Tatiana

*Tatiana Pinedo Rivera, PhD* (she/her/hers)
Nanolithography and Characterisation Team Leader
Senior Process Engineer

Melbourne Centre for Nanofabrication
ANFF Victoria
151 Wellington Road, Clayton VIC 3168 Australia

P: +61 (0)3 9905 9660
E: tatiana.pinedo at nanomelbourne.com
W: http://nanomelbourne.com




On Sat, 8 Oct 2022 at 02:49, Tony L Olsen <tony.olsen at utah.edu> wrote:

> There are lots of options, but for years we?ve been using TechNitrile
> TN2000 Series gloves (both white and blue) from TechNiGlove International.
> Like most alternatives, they have microtextured fingertips, which are not
> visible to the naked eye, but we?ve been happy with them.  I don?t recall
> any complaints about grip.  They are available through various suppliers.
>
>
>
> tonyO
>
>
>
>
>
> Tony Olsen
>
> Nanofab Cleanroom Supervisor/Process Engineer
>
> University of Utah
>
> 36 S Wasatch Drive, Suite 2500
>
> Salt Lake City, UT  84112
>
> 801-587-0651
>
> www.nanofab.utah.edu
>
>
>
>
>
>
>
> *From:* Football <yaofootball at gmail.com>
> *Sent:* Thursday, October 6, 2022 11:11
> *To:* labnetwork at mtl.mit.edu
> *Subject:* [labnetwork] Cleanroom gloves
>
>
>
> Dear Colleague,
>
>
>
> I wonder what brands and types of cleanroom gloves you use in your
> cleanroom. At Argonne, we have been using the *Kimberly-Clark
> Professional? Kimtech? Pure G5 Blue Cleanroom Nitrile Gloves. *Some time
> back we noticed that these blue ones were discontinued by the manufacturer,
> then we started to use the *Kimberly-Clark Professional? Kimtech? Pure G3
> Cleanroom NXT? Nitrile Gloves. *Besides the pros that this G3 type is
> less expensive and releases less particles than the G5 blue ones, some
> users noticed the difference in the grip strength of these two. The G3 has
> a smooth finish while the G5 blue has a more coarse finish which some users
> think has provided more grip strength.
>
>
>
> Thanks!
>
> *Fubo Rao, Ph.D.,*
>
> *Nanofabrication Cleanroom Manager,*
>
> *Center for Nanoscale Materials,*
>
> *Argonne National Laboratory*
>
> *9700 S. Cass Ave, Lemont, IL 60439*
>
> *Phone: 630-252-5708*
>
> *Email: frao at anl.gov <http://frao at anl.gov>*
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221010/88c14040/attachment.html>

From gheorghe.iordache at infim.ro  Mon Oct 10 03:18:11 2022
From: gheorghe.iordache at infim.ro (Gheorghe IORDACHE)
Date: Mon, 10 Oct 2022 10:18:11 +0300
Subject: [labnetwork] Cleanroom gloves
In-Reply-To: <BYAPR11MB3496E86D02931426A60403C5F15F9@BYAPR11MB3496.namprd11.prod.outlook.com>
References: <CAOycKMZgLwJeNyVXGdsOmeMu3_Y8zT7YQY5oGuvyMEYEv3Xdjg@mail.gmail.com>
 <BYAPR11MB3496E86D02931426A60403C5F15F9@BYAPR11MB3496.namprd11.prod.outlook.com>
Message-ID: <003001d8dc78$74490b80$5cdb2280$@infim.ro>

Hi Tony,

I still recall at the UGIM 2018 Greg Heiland?s comprehensive talk on this particular topic: ?How To Select Appropriate Gloves & Wipes?.

You may contact him directly on Linkedin or see a short video here:

https://www.linkedin.com/posts/valutek_what-cleanroom-glove-offers-the-most-comfort-activity-6912130945194065921-FnRn?utm_source=share <https://www.linkedin.com/posts/valutek_what-cleanroom-glove-offers-the-most-comfort-activity-6912130945194065921-FnRn?utm_source=share&utm_medium=member_desktop> &utm_medium=member_desktop 

Good luck,

Gheorghe Iordache

https://www.linkedin.com/in/gheorghe-iordache-phd-physics-mba/ 

 

From: labnetwork [mailto:labnetwork-bounces at mtl.mit.edu] On Behalf Of Tony L Olsen
Sent: Friday, October 7, 2022 6:10 PM
To: Football <yaofootball at gmail.com>; labnetwork at mtl.mit.edu
Subject: Re: [labnetwork] Cleanroom gloves

 

There are lots of options, but for years we?ve been using TechNitrile TN2000 Series gloves (both white and blue) from TechNiGlove International.  Like most alternatives, they have microtextured fingertips, which are not visible to the naked eye, but we?ve been happy with them.  I don?t recall any complaints about grip.  They are available through various suppliers.

 

tonyO

 

 

Tony Olsen

Nanofab Cleanroom Supervisor/Process Engineer

University of Utah

36 S Wasatch Drive, Suite 2500

Salt Lake City, UT  84112

801-587-0651

www.nanofab.utah.edu

 

 

 

From: Football <yaofootball at gmail.com <mailto:yaofootball at gmail.com> > 
Sent: Thursday, October 6, 2022 11:11
To: labnetwork at mtl.mit.edu <mailto:labnetwork at mtl.mit.edu> 
Subject: [labnetwork] Cleanroom gloves

 

Dear Colleague,

 

I wonder what brands and types of cleanroom gloves you use in your cleanroom. At Argonne, we have been using the Kimberly-Clark Professional? Kimtech? Pure G5 Blue Cleanroom Nitrile Gloves. Some time back we noticed that these blue ones were discontinued by the manufacturer, then we started to use the Kimberly-Clark Professional? Kimtech? Pure G3 Cleanroom NXT? Nitrile Gloves. Besides the pros that this G3 type is less expensive and releases less particles than the G5 blue ones, some users noticed the difference in the grip strength of these two. The G3 has a smooth finish while the G5 blue has a more coarse finish which some users think has provided more grip strength.  

 

Thanks!

Fubo Rao, Ph.D.,

Nanofabrication Cleanroom Manager,

Center for Nanoscale Materials,

Argonne National Laboratory

9700 S. Cass Ave, Lemont, IL 60439

Phone: 630-252-5708

Email: frao at anl.gov



-- 
This email has been checked for viruses by Avast antivirus software.
www.avast.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221010/12333d5f/attachment.html>

From ericdj at seas.upenn.edu  Mon Oct 10 14:30:54 2022
From: ericdj at seas.upenn.edu (Eric Johnston)
Date: Mon, 10 Oct 2022 14:30:54 -0400
Subject: [labnetwork] Microfabrication class
In-Reply-To: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
References: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
Message-ID: <CABtcwD-TcDuPEZm_75ye-ww-sSUTmnw3x+Kh0PQKJDO365vOEA@mail.gmail.com>

Hi Sergi

We have done a soft lithography workshop for a while. A couple of things
that worked for us:

- Limit attendance to 6.
- Lecture is about 45 minutes, then we have a hand-on workshop that takes
about 3+ hours.
- We provide the mask, wafers, resist, and PDMS.
- We do not test the devices, which would take much too long.
- We charge for attendance, ~$50 per attendee. This was mostly to reduce
no-shows. Eventbrite makes it easy to sign up and to charge.

I can share my protocol and powerpoint if you like.

Best Regards

Eric

Eric Johnston
Interim Director
Quattrone Nanofabrication Facility
Singh Center for Nanotechnology
University of Pennsylvania
3205 Walnut Street, #116
ericdj at seas.upenn.edu
T. 215.573.6695

On Fri, Oct 7, 2022 at 3:38 PM Sergi Lendinez <sergilendi at lsu.edu> wrote:

> Dear labnetwork community,
>
>
>
> Here at LSU we are planning to start a microfabrication class soon, and I
> would like to ask for your opinions about setting up this kind of class at
> a university. I am not sure if this topic has been discussed here before,
> so I apologize for any possible duplication.
>
>
> Any information would be very helpful, like do's and don't's, devices
> being fabricated, number of students, students/teacher ratio, course load,
> etc.
>
>
> I'd like to fabricate some CMOS device, but we lack some critical
> equipment such as a diffusion tube furnace, cvd, or packaging tools, so I'm
> looking for alternate ideas: maybe a photodiode/detector, a Hall sensor or
> some micro-fluidic channels. If anyone has some experience fabricating
> these devices in a class setup, is there anything you'd be willing to share?
>
>
> Many thanks,
>
> Sergi
>
>
>
> *---*
>
> *Sergi Lendinez, Ph. D.*
> Assistant Director NFF | Louisiana State University
>
> Center for Advanced Microstructures and Devices (CAMD)
>
> 6980 Hefferson Highway, Baton Rouge, LA 70803
> (225) 578-9378
>
> sergilendi at lsu.edu | *lsu.edu/nanofabrication*
> <https://urldefense.com/v3/__https://lsu.edu/nanofabrication__;!!IBzWLUs!XghTGOjN4El_vJnH6I5fwfzt9SqdTyqCL-YzUbJoF8dokpSDKpQgVgP4r7QVnXIWK7uhkUaPmk8WYpHL9Bp-4WM$>
>
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
>
> https://urldefense.com/v3/__https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork__;!!IBzWLUs!XghTGOjN4El_vJnH6I5fwfzt9SqdTyqCL-YzUbJoF8dokpSDKpQgVgP4r7QVnXIWK7uhkUaPmk8WYpHLmAp5dC0$
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221010/daf3ee57/attachment.html>

From gae at smu.edu  Mon Oct 10 18:14:32 2022
From: gae at smu.edu (Evans, Gary)
Date: Mon, 10 Oct 2022 22:14:32 +0000
Subject: [labnetwork] Microfabrication class
In-Reply-To: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
References: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
Message-ID: <0BF5A84A-AD36-4307-B6DA-CCF959A924BA@smu.edu>

Hi Sergi,
As part of a junior level lecture course on semiconductors (at the Streetman/Bannerjee level), the lab portion of the course has students fabricating p-channel MOSFET transistors on 4? (100 mm) wafers using a 4 mask level process.  I am attaching the traveler that is being used this semester.  Typically there are 10 labs over the 15 week semester, with the devices being tested in the last lab.  Enrollment is limited to about 28 students because we limit the number of students in the clean room to 4 students at a time, and having 7 lab sessions outside of class lectures a week is about the scheduling limit.  The lab sessions are nominally 2 hours, but often shorter and occasionally longer.  I always try to have two experienced Teaching Assistants in each lab session for safety.  You likely can get a donated furnace for diffusion (we use spin on boron) and oxidation.  We have a sputter system to deposit Al for contacts.  Most of the time testing consists of just probe-testing at the wafer level.  A few times we have diced up the wafer and mounted some transistors on TO headers.

I also teach a compound semiconductor course and in the lab portion of that course we fab InP based HBTs, GaAs based HEMPTs and semiconductor lasers (GaAs or InP based).  In a 15 week semester, we can easily fab any two types of devices, although on occasion we have done all three.  IntelliEPI generously provides the epitaxial material.  These devices only require photolithography, wet etching and metallization (TiAu, e-beam deposited).  If interested I can send the process travelers for these devices, too.
If you want more information (mask details, course syllabus?)  let me know or just give me a call.
Best Regards,
Gary Evans
Professor
Southern Methodist University
214 768 3032 (o)
214 207 9427 (cell)

On Oct 7, 2022, at 12:39 PM, Sergi Lendinez <sergilendi at lsu.edu<mailto:sergilendi at lsu.edu>> wrote:


[EXTERNAL SENDER]

Dear labnetwork community,



Here at LSU we are planning to start a microfabrication class soon, and I would like to ask for your opinions about setting up this kind of class at a university. I am not sure if this topic has been discussed here before, so I apologize for any possible duplication.

Any information would be very helpful, like do's and don't's, devices being fabricated, number of students, students/teacher ratio, course load, etc.

I'd like to fabricate some CMOS device, but we lack some critical equipment such as a diffusion tube furnace, cvd, or packaging tools, so I'm looking for alternate ideas: maybe a photodiode/detector, a Hall sensor or some micro-fluidic channels. If anyone has some experience fabricating these devices in a class setup, is there anything you'd be willing to share?

Many thanks,
Sergi



---
Sergi Lendinez, Ph. D.
Assistant Director NFF | Louisiana State University
Center for Advanced Microstructures and Devices (CAMD)
6980 Hefferson Highway, Baton Rouge, LA 70803
(225) 578-9378
sergilendi at lsu.edu<mailto:sergilendi at lsu.edu> | lsu.edu/nanofabrication<https://lsu.edu/nanofabrication>



_______________________________________________
labnetwork mailing list
labnetwork at mtl.mit.edu<mailto:labnetwork at mtl.mit.edu>
https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221010/18ad28a7/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: MOSFETFab_Fall2022_Revised_September_12.pptx
Type: application/vnd.openxmlformats-officedocument.presentationml.presentation
Size: 1831952 bytes
Desc: MOSFETFab_Fall2022_Revised_September_12.pptx
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221010/18ad28a7/attachment.pptx>

From philipp.altpeter at physik.uni-muenchen.de  Tue Oct 11 04:02:11 2022
From: philipp.altpeter at physik.uni-muenchen.de (Philipp Altpeter)
Date: Tue, 11 Oct 2022 10:02:11 +0200
Subject: [labnetwork] Microfabrication class
In-Reply-To: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
References: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
Message-ID: <3df90d2e-8cb6-553a-a0c9-2d740746154a@physik.uni-muenchen.de>

Dear Sergi,

One of the simplest devices that could be fabricated within a 
microfabrication class would be a metal, thin film temperature sensor: 
etching a meander in a thin metal film such as Aluminum (involving thin 
film deposition, photolithography and wet etching or lift-off), bonding 
the device in a chip carrier and measure it on a hot plate. Very simple, 
very straight forward, you start with a (piece of) Wafer and end up with 
a somewhat functional device.

Best,

Philipp


Am 07.10.2022 um 19:39 schrieb Sergi Lendinez:
>
> Dear labnetwork community,
>
> Here at LSU we are planning to start a microfabrication class soon, 
> and I would like to ask for your opinions about setting up this kind 
> of class at a university. I am not sure if this topic has been 
> discussed here before, so I apologize for any possible duplication.
>
>
> Any information would be very helpful, like do's and don't's, devices 
> being fabricated, number of students, students/teacher ratio, course 
> load, etc.
>
>
> I'd like to fabricate some CMOS device, but we lack some critical 
> equipment such as a diffusion tube furnace, cvd, or packaging tools, 
> so I'm looking for alternate ideas: maybe a photodiode/detector, a 
> Hall sensor or some micro-fluidic channels. If anyone has some 
> experience fabricating these devices in a class setup, is there 
> anything you'd be willing to share?
>
>
> Many thanks,
>
> Sergi
>
> *---***
>
> *Sergi Lendinez, Ph. D.*
> Assistant Director NFF | Louisiana State University
>
> Center for Advanced Microstructures and Devices (CAMD)
>
> 6980 Hefferson Highway, Baton Rouge, LA 70803
> (225) 578-9378
>
> sergilendi at lsu.edu<mailto:sergilendi at lsu.edu>| 
> *lsu.edu/nanofabrication*<https://lsu.edu/nanofabrication>
>
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork

-- 
Philipp Altpeter
Fakult?t f?r Physik der LMU und
Center for NanoScience (CeNS)
LS Prof. Efetov
Geschwister-Scholl-Platz 1
D-80539 M?nchen
T. +49 (0)89 2180-3733
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221011/5f7f9439/attachment.html>

From mbradash at purdue.edu  Tue Oct 11 14:35:10 2022
From: mbradash at purdue.edu (Bradash, Mihailo Rayko)
Date: Tue, 11 Oct 2022 18:35:10 +0000
Subject: [labnetwork] Cambridge Nanotech Fiji ALD precursor pressures
Message-ID: <MW5PR22MB31537AD81A2A5E866B232188A1239@MW5PR22MB3153.namprd22.prod.outlook.com>

Hello,

I was wondering if anyone here has had any experience with monitoring the precursor gas pressures in a Cambridge Nanotech Fiji ALD? I am using 4021Hafnium> Tetrakis(dimethylamino)hafnium, 98+%, contained in 50 ml Swagelok(r) cylinder and want to know if anyone happen to have a base pressure supplied by the cylinder, and what pressures have you seen before failing/empty? I recently came into this tool and position middle of this year and do not have enough data to for a trend analysis.

Mihailo Bradash
Research Engineer
Purdue University
Birck Nanotechnology Center
1205 W. State Street
West Lafayette, Indiana 47907
Office: (765)494-6522
Cell: (219)670-4974
mbradash at purdue.edu<mailto:mbradash at purdue.edu>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221011/802bfbfc/attachment.html>

From yaofootball at gmail.com  Tue Oct 11 18:11:18 2022
From: yaofootball at gmail.com (Football)
Date: Tue, 11 Oct 2022 17:11:18 -0500
Subject: [labnetwork] Microfabrication class
In-Reply-To: <3df90d2e-8cb6-553a-a0c9-2d740746154a@physik.uni-muenchen.de>
References: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
 <3df90d2e-8cb6-553a-a0c9-2d740746154a@physik.uni-muenchen.de>
Message-ID: <CAOycKMYGVgkqT83OZ9wco6VvjuJiRhL4kw-6KQckwqa8Gauj1w@mail.gmail.com>

Hi Sergi,

What I did before is to teach undergraduates how to fabricate Ni-Cr
thermocouples on 4" wafers. The idea was similar to Philipp's. The goal was
to make a simple device but would need most of the commonly used microfab
procedures. The Ni-Cr thermocouple fabrication needed mask design, wafer
cleaning, oxidation, spin-coating, photolithography with alignments
(provided more complexity), film deposition, and wet etching, etc. End of
the day students get a wafer diced and many devices. Then we tested a few
of them to see if it works and what the temperature response curve was.

Thanks,



*Fubo Rao, Ph.D.,*

*Nanofabrication Cleanroom Manager,*

*Center for Nanoscale Materials,*

*Argonne National Laboratory*

*9700 S. Cass Ave, Lemont, IL 60439*

*Phone: 630-252-5708*

*Email: **frao at anl.gov* <frao at anl.gov>

On Tue, Oct 11, 2022 at 6:40 AM Philipp Altpeter <
philipp.altpeter at physik.uni-muenchen.de> wrote:

> Dear Sergi,
>
> One of the simplest devices that could be fabricated within a
> microfabrication class would be a metal, thin film temperature sensor:
> etching a meander in a thin metal film such as Aluminum (involving thin
> film deposition, photolithography and wet etching or lift-off), bonding the
> device in a chip carrier and measure it on a hot plate. Very simple, very
> straight forward, you start with a (piece of) Wafer and end up with a
> somewhat functional device.
>
> Best,
>
> Philipp
>
>
> Am 07.10.2022 um 19:39 schrieb Sergi Lendinez:
>
> Dear labnetwork community,
>
>
>
> Here at LSU we are planning to start a microfabrication class soon, and I
> would like to ask for your opinions about setting up this kind of class at
> a university. I am not sure if this topic has been discussed here before,
> so I apologize for any possible duplication.
>
>
> Any information would be very helpful, like do's and don't's, devices
> being fabricated, number of students, students/teacher ratio, course load,
> etc.
>
>
> I'd like to fabricate some CMOS device, but we lack some critical
> equipment such as a diffusion tube furnace, cvd, or packaging tools, so I'm
> looking for alternate ideas: maybe a photodiode/detector, a Hall sensor or
> some micro-fluidic channels. If anyone has some experience fabricating
> these devices in a class setup, is there anything you'd be willing to share?
>
>
> Many thanks,
>
> Sergi
>
>
>
> *---*
>
> *Sergi Lendinez, Ph. D.*
> Assistant Director NFF | Louisiana State University
>
> Center for Advanced Microstructures and Devices (CAMD)
>
> 6980 Hefferson Highway, Baton Rouge, LA 70803
> (225) 578-9378
>
> sergilendi at lsu.edu | *lsu.edu/nanofabrication*
> <https://lsu.edu/nanofabrication>
>
>
>
> _______________________________________________
> labnetwork mailing listlabnetwork at mtl.mit.eduhttps://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>
> --
> Philipp Altpeter
> Fakult?t f?r Physik der LMU und
> Center for NanoScience (CeNS)
> LS Prof. Efetov
> Geschwister-Scholl-Platz 1
> D-80539 M?nchen
> T. +49 (0)89 2180-3733
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221011/58726542/attachment.html>

From jtmitch5 at ncsu.edu  Wed Oct 12 07:22:53 2022
From: jtmitch5 at ncsu.edu (James Mitchell)
Date: Wed, 12 Oct 2022 07:22:53 -0400
Subject: [labnetwork] Cambridge Nanotech Fiji ALD precursor pressures
In-Reply-To: <MW5PR22MB31537AD81A2A5E866B232188A1239@MW5PR22MB3153.namprd22.prod.outlook.com>
References: <MW5PR22MB31537AD81A2A5E866B232188A1239@MW5PR22MB3153.namprd22.prod.outlook.com>
Message-ID: <CAEXS_M9WJK3=Sdcd6hpMckYfYzdXVQz7gfKk+eRAWzRMMdp8Nw@mail.gmail.com>

The best way to know if the precursor is empty is to weigh it.
Should have a tare weight on it. Another way is to look for a spike in
pressure during the pulse step.
This only works if you are not flowing too much gas.

Jim

On Tue, Oct 11, 2022 at 7:36 PM Bradash, Mihailo Rayko <mbradash at purdue.edu>
wrote:

> Hello,
>
>
>
> I was wondering if anyone here has had any experience with monitoring the
> precursor gas pressures in a Cambridge Nanotech Fiji ALD? I am using
> 4021Hafnium> Tetrakis(dimethylamino)hafnium, 98+%, contained in 50 ml
> Swagelok? cylinder and want to know if anyone happen to have a base
> pressure supplied by the cylinder, and what pressures have you seen before
> failing/empty? I recently came into this tool and position middle of this
> year and do not have enough data to for a trend analysis.
>
>
>
> Mihailo Bradash
>
> Research Engineer
>
> Purdue University
>
> Birck Nanotechnology Center
>
> 1205 W. State Street
>
> West Lafayette, Indiana 47907
>
> Office: (765)494-6522
>
> Cell: (219)670-4974
>
> mbradash at purdue.edu
>
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>


-- 
*Thank you, Jim*

*James Mitchell*
*Specialty Trades Technician*
*Dept. of Electrical and Computer Engineering*
*North Carolina State University Nanofabrication Facility (NNF)*
*MRC RM243A **Box 7911*
*2410 Campus Shore Dr., Raleigh, NC 27606*
*jtmitch5 at ncsu.edu* <jtmitch5 at ncsu.edu>
*Desk: 919-515-5394*
*Cell: 919-717-7325*
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221012/4eb594bd/attachment.html>

From James.Grant at glasgow.ac.uk  Wed Oct 12 08:02:03 2022
From: James.Grant at glasgow.ac.uk (James Grant)
Date: Wed, 12 Oct 2022 12:02:03 +0000
Subject: [labnetwork] Cambridge Nanotech Fiji ALD precursor pressures
In-Reply-To: <CAEXS_M9WJK3=Sdcd6hpMckYfYzdXVQz7gfKk+eRAWzRMMdp8Nw@mail.gmail.com>
References: <MW5PR22MB31537AD81A2A5E866B232188A1239@MW5PR22MB3153.namprd22.prod.outlook.com>
 <CAEXS_M9WJK3=Sdcd6hpMckYfYzdXVQz7gfKk+eRAWzRMMdp8Nw@mail.gmail.com>
Message-ID: <LO4P265MB610836F9D005DD9A4F24E010B0229@LO4P265MB6108.GBRP265.PROD.OUTLOOK.COM>

Hello all,

Agree with James Mitchell.

Best way to is remove bottle and weigh it.

Only other way to know if bottle is getting empty is to use residual gas analyzer to analyse chemical fingerprint in ALD chamber.  Not seen it in practice. Also good for process development to know how long you need to purge precursor/plasma/water.

We normally find out our precursor is empty by using ellipsometer to measure film thickness and finding out it is almost < 1 nm!

Cheers,

James

Dr. James Paul Grant
Research Engineer in Plasma Processing

Plasma Etch Group
 james.grant at glasgow.ac.uk<mailto:james.grant at glasgow.ac.uk>

 [cid:image001.png at 01D8DE3A.D2215960]
      www.JWNC.gla.ac.uk<http://www.jwnc.gla.ac.uk/>
[cid:image002.png at 01D8DE3A.D2215960]  LinkedIn.com/company/JWNC
[cid:image003.png at 01D8DE3A.D2215960]  @UofG_JWNC<https://twitter.com/uofg_jwnc>

From: labnetwork <labnetwork-bounces at mtl.mit.edu> On Behalf Of James Mitchell
Sent: 12 October 2022 12:23
To: Bradash, Mihailo Rayko <mbradash at purdue.edu>
Cc: labnetwork at mtl.mit.edu
Subject: Re: [labnetwork] Cambridge Nanotech Fiji ALD precursor pressures

The best way to know if the precursor is empty is to weigh it.
Should have a tare weight on it. Another way is to look for a spike in pressure during the pulse step.
This only works if you are not flowing too much gas.

Jim

On Tue, Oct 11, 2022 at 7:36 PM Bradash, Mihailo Rayko <mbradash at purdue.edu<mailto:mbradash at purdue.edu>> wrote:
Hello,

I was wondering if anyone here has had any experience with monitoring the precursor gas pressures in a Cambridge Nanotech Fiji ALD? I am using 4021Hafnium> Tetrakis(dimethylamino)hafnium, 98+%, contained in 50 ml Swagelok? cylinder and want to know if anyone happen to have a base pressure supplied by the cylinder, and what pressures have you seen before failing/empty? I recently came into this tool and position middle of this year and do not have enough data to for a trend analysis.

Mihailo Bradash
Research Engineer
Purdue University
Birck Nanotechnology Center
1205 W. State Street
West Lafayette, Indiana 47907
Office: (765)494-6522
Cell: (219)670-4974
mbradash at purdue.edu<mailto:mbradash at purdue.edu>

_______________________________________________
labnetwork mailing list
labnetwork at mtl.mit.edu<mailto:labnetwork at mtl.mit.edu>
https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork


--
Thank you, Jim

James Mitchell
Specialty Trades Technician
Dept. of Electrical and Computer Engineering
North Carolina State University Nanofabrication Facility (NNF)
MRC RM243A Box 7911
2410 Campus Shore Dr., Raleigh, NC 27606
jtmitch5 at ncsu.edu<mailto:jtmitch5 at ncsu.edu>
Desk: 919-515-5394
Cell: 919-717-7325

[Image removed by sender.]
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221012/700c2c9a/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: ~WRD0004.jpg
Type: image/jpeg
Size: 823 bytes
Desc: ~WRD0004.jpg
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221012/700c2c9a/attachment.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.png
Type: image/png
Size: 26666 bytes
Desc: image001.png
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221012/700c2c9a/attachment.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image002.png
Type: image/png
Size: 1538 bytes
Desc: image002.png
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221012/700c2c9a/attachment-0001.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image003.png
Type: image/png
Size: 1717 bytes
Desc: image003.png
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221012/700c2c9a/attachment-0002.png>

From peter.avis at maine.edu  Thu Oct 13 08:58:58 2022
From: peter.avis at maine.edu (Peter Avis)
Date: Thu, 13 Oct 2022 08:58:58 -0400
Subject: [labnetwork] Position at the University of Maine
Message-ID: <CALMs=uVa2gBuEsvGOandf+iWz2SrskE5E9FMcyL_ntNVUprgbw@mail.gmail.com>

Dear  Microfab Lab Network,

I write to share a position that we have open currently and we welcome any
interested to apply.  See below for the link and description.

Best, Pete

https://umaine.hiretouch.com/job-details?jobid=79158



*University of Maine*

*Job Description*



*Title:               *Research Facilities Operational Specialist

*Department: *Coordinated Operating Research Entities

*Reports To:    *CORE Director and FIRST Director

*Date:               *October 2022



*Purpose:* To support the operational aspects of research facilities that
are associated with research and development activities in CORE and FIRST,
including the Microfabrication Cleanroom Facility and associated synthesis,
fabrication, and characterization facilities.  The responsibilities will
include development and refinement of fabrication processes and
characterization techniques within the facilities, as well as operation and
maintenance of a broad range of equipment in these areas.  This position
also provides expertise and training to users of the CORE Microfabrication
Cleanroom and associated FIRST facilities.



*Essential Duties and Responsibilities:*

?       *Operational Support,* *Student Training, and Equipment
Oversight: *Operates
and maintains thin-film fabrication and elemental and materials
characterization equipment and related software, provides training to
students and staff on equipment use, sample preparation, and data
analysis.  Management duties may include direct supervision of student
employees.

?       *Research Support: *Serves as a technical resource for
(under)graduate students, staff, and faculty within CORE and FIRST.
Collaborates with and advises internal and external entities to support
research and provides hands-on assistance/training to researchers.
Provides assistance related to funding opportunities.

?       *Safety and Compliance: *Trains and/or supervises facility users in
safe lab practices, develops and documents lab-specific safety trainings,
develops and documents facility standard operating procedures (SOP),
maintains chemical and equipment inventories.  Serves as building safety
officer for CORE and FIRST and may serve on the University Radiation Safety
Committee.

?       *Method Development: *Develops in-demand analysis and/or
fabrication methods to meet research goals specific to client needs,
develops project-specific quality control/quality assurance plans to ensure
consistent and reliable results, identifies new opportunities for service
offerings and develops and executes plan to bring services to market.

?       *Client Development and Retention: *Promotes CORE services and
develops an active user base both internal and external to UMaine, liaises
with clients to develop research plans & identify the revenue-generating
services that can be completed, communicates data/results in meaningful
formats and discusses data analysis and future experiment/research goals.

?       *Business Support: *Coordinates with UM CORE to manage Cleanroom
Facility accounting, finances, rate development, and billing operations.

?       Performs other reasonably related duties as assigned.



*Knowledge and Skill Requirements:*



*Required: *

?       Master of Science degree in the Physical Sciences or Engineering
and three years of relevant professional experience or a Bachelor of
Science degree in the Physical Sciences or Engineering with more than five
years of relevant professional experience.

?       Knowledge and experience must include expertise in *two of the
following areas*:

o   Lithography techniques (photo- and/or electron), wet- and/or plasma
etch techniques, metal/dielectric thin film deposition, wafer bonding,
and/or vacuum systems; and

o   X-ray and/or electron spectroscopies, microscopies, surface
characterization techniques such as XRD, XPS, and/or SEM analysis.

?       Strong analytical and problem-solving skills, the proven ability to
succeed in developing practical solutions that will lead to technology
innovations and development.

?       Demonstrated ability to work collaboratively in an R&D environment.

?       Excellent communication skills, proven organizational skills, and
demonstrated ability to write high-impact publications, reports and/or
whitepapers.

?       Significant experience in project management, including
establishing design of experiments and documenting processes.

?       Experience in dealing with hazardous materials and establishing
safe operating procedures.

*Preferred:*

?       PhD in Physics, Electrical Engineering, Chemistry, Materials
Science and Engineering, or related field.

?       Prior experience managing a laboratory facility and fostering
collaborative interactions with clients or stakeholders.

?       Demonstrated ability to effectively train and supervise staff or
students.

?       Curiosity and capability to research and learn new techniques or
technical topics, as needed.

?       Proficient in a scientific programming environment (ex. Julia,
Python) and/or data set analysis tools (ex. JMP, R).

*Work Environment:* The primary site of work will be on-campus facilities
at the University of Maine, with occasional travel to field and training
sites in Maine and the Northeast Region.



*Work Schedule: *Normal University of Maine business hours are Monday
through Friday 8:00 am to 4:30 pm.  Work outside of normal business hours
may be necessary in order to complete the requirements of the position and
may include occasional nights and weekends.



*Position Type: *On-going, full-time, base budgeted.


*Work Year:* Full-time, fiscal year position.



*Performance Evaluation Schedule: *Performance evaluation will be conducted
according to the UMPSA agreement.



*Job Family/Salary Grade: *07/05.



Appropriate background checks are required.



All UMS employees are required to comply with applicable policies and
procedures, as well as to complete applicable workplace related screenings,
and required employee trainings, such as Information Security, Safety
Training, Workplace Violence, and Sexual Harassment.






-- 
Peter Avis, PhD
CORE Director
https://umaine.edu/core/
Undergraduate Education Coordinator Maine-eDNA
University of Maine
Orono, ME
o phone: 207-581-2251
c phone: 651-307-6327
he/him
The University of Maine recognizes that it is located on Marsh Island in
the homeland of the Penobscot Nation, where issues of water and territorial
rights, and encroachment upon sacred sites, are ongoing. Penobscot homeland
is connected to the other Wabanaki Tribal Nations ? the Passamaquoddy,
Maliseet, and Micmac ? through kinship, alliances and diplomacy. The
university also recognizes that the Penobscot Nation and the other Wabanaki
Tribal Nations are distinct, sovereign, legal and political entities with
their own powers of self-governance and self-determination.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221013/7f4e26fa/attachment.html>

From eric.fluckiger at utah.edu  Thu Oct 13 13:57:00 2022
From: eric.fluckiger at utah.edu (Eric Fluckiger)
Date: Thu, 13 Oct 2022 11:57:00 -0600
Subject: [labnetwork] Cambridge Fiji ALD problems
Message-ID: <CAPx0RS-v8jZqecE-4eZ78mu4Mmm-ojZvvQtEfmpaVpRgQW65sg@mail.gmail.com>

Dear colleagues,

I have a Cambridge Fiji F200 ALD that has traditionally had driver issues
when turning on the encoder and making the handshake with the Windows PC.
These driver errors have gone so far as to corrupt the hard drive on the
computer, but, I have always been able to reinstall Windows from the BIOS
and get the tool to communicate with the PC.

Just recently, some routine maintenance was performed and the tool was shut
down from the power source (breakers were turned off). Now, after
repowering the tool (following the startup procedure from the manual), the
computer does not have any of the configuration settings (MFC, heater, and
valve locations along with upper and lower limits). Even though the tool
makes the USB connection to the PC when the image of the reactor tries to
load, it disappears and is replaced with what I can only assume is the
default image with no configuration (see attached image). Also, when I go
to load a recipe, it tells me that my recipe parameters are outside of the
upper/lower limits of 0/0.

After reading the manual, I noticed that my software is missing the
"service" tab that allows you to make the configuration and push it to the
tool.

My question: is the configuration for the reactor/MFCs/heaters stored on
the Windows PC that interfaces with the tool, or, is that information
stored on the E-box inside the tool? I have tried reinstalling Windows
several times as well using a different computer and each time the reactor
tries to load the configuration and fails.

Follow-up question: I have reached out to Veeco for technical support
through their support webpage and have not received a response. Does anyone
have any contacts or ALD SMEs that would be able to help me get my ALD back
online?

I would be grateful for any insights or help with regard to this matter.

Yours truly,
Eric Fluckiger
Process Engineer
Utah Nanofab


A picture of what my computer is showing after a successful USB handshake.
Note: the service tab is missing on my software.

[image: IMG_3113 (1).jpg]


The missing system configuration tab. This picture was taken from Fiji
Manual
<https://is.muni.cz/el/1431/jaro2017/F4280/um/69248846/69248852/FIJI_F200_ALD.pdf>.
This is what leads me to believe that the configuration settings are stored
on the tool itself (E-box).

[image: Capture.JPG]
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221013/955f2b48/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: IMG_3113 (1).jpg
Type: image/jpeg
Size: 343196 bytes
Desc: not available
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221013/955f2b48/attachment.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Capture.JPG
Type: image/jpeg
Size: 116101 bytes
Desc: not available
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221013/955f2b48/attachment.jpe>

From edeguns at gmail.com  Thu Oct 13 19:09:16 2022
From: edeguns at gmail.com (Eric Deguns)
Date: Thu, 13 Oct 2022 19:09:16 -0400
Subject: [labnetwork] Cambridge Fiji ALD problems
In-Reply-To: <CAPx0RS-v8jZqecE-4eZ78mu4Mmm-ojZvvQtEfmpaVpRgQW65sg@mail.gmail.com>
References: <CAPx0RS-v8jZqecE-4eZ78mu4Mmm-ojZvvQtEfmpaVpRgQW65sg@mail.gmail.com>
Message-ID: <4F9DD3D8-B39D-4F12-9521-00AC849DEF48@gmail.com>

An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221013/be49f9a4/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: IMG_3113 (1).jpg
Type: image/jpeg
Size: 343196 bytes
Desc: not available
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221013/be49f9a4/attachment.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Capture.JPG
Type: image/jpeg
Size: 116101 bytes
Desc: not available
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221013/be49f9a4/attachment.jpe>

From logence at uc.cl  Thu Oct 13 21:17:41 2022
From: logence at uc.cl (=?UTF-8?B?RHIuIExvw69rIEdlbmNl?=)
Date: Thu, 13 Oct 2022 22:17:41 -0300
Subject: [labnetwork] Microfabrication class
In-Reply-To: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
References: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
Message-ID: <459f3b64-7f8f-7f93-c131-90988b078ccc@uc.cl>

Dear Sergi,

I started a few years ago microfabrication Classes for engineers and 
experimental physicists, here at UC. our cleanroom is small, with CMOS 
or III-V standard processes. Thus we have more flexibility about 
materials and processes. ? We did microfluidics devices pump (with ITO 
electrodes), graphene transistors (using comercial monolayer), and basic 
MEMS with Si anisotropic etching, and simple micro-electrodes. Most of 
the time, the devices are not working very well, but It allows the 
students to go through mask design, spin-coating, (use of tweezers!), 
photolithography, thin-film deposition, wet etching, and electrical 
characterization. I think the graphene-based devices are quite simple to 
fabricate and and always include an important electrical 
characterization part. Microfluidics devices are fantastic for students 
if they have the possibility to characterize under microscope the 
channels with micro-particles for instance...

Hope it helps!


Best,

Lo?k





Le 07/10/2022 ? 14:39, Sergi Lendinez a ?crit?:
>
> Dear labnetwork community,
>
> Here at LSU we are planning to start a microfabrication class soon, 
> and I would like to ask for your opinions about setting up this kind 
> of class at a university. I am not sure if this topic has been 
> discussed here before, so I apologize for any possible duplication.
>
>
> Any information would be very helpful, like do's and don't's, devices 
> being fabricated, number of students, students/teacher ratio, course 
> load, etc.
>
>
> I'd like to fabricate some CMOS device, but we lack some critical 
> equipment such as a diffusion tube furnace, cvd, or packaging tools, 
> so I'm looking for alternate ideas: maybe a photodiode/detector, a 
> Hall sensor or some micro-fluidic channels. If anyone has some 
> experience fabricating these devices in a class setup, is there 
> anything you'd be willing to share?
>
>
> Many thanks,
>
> Sergi
>
> *---***
>
> *Sergi Lendinez, Ph. D.*
> Assistant Director NFF | Louisiana State University
>
> Center for Advanced Microstructures and Devices (CAMD)
>
> 6980 Hefferson Highway, Baton Rouge, LA 70803
> (225) 578-9378
>
> sergilendi at lsu.edu<mailto:sergilendi at lsu.edu>| 
> *lsu.edu/nanofabrication*<https://lsu.edu/nanofabrication>
>
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork

-- 
Dr. Lo?k Gence
Assistant Professor
Functional Materials & Devices Lab
Pontificia Universidad Cat?lica de Chile
Avda. Vicu?a Mackenna 4860,
CP 7820436 Santiago
Lab: +56 95504 9648
www.lgdeviceslab.com

-- 
No sienta la obligaci?n de contestar este mail fuera de horario laboral.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221013/ab84b3e5/attachment.html>

From carsen at stanford.edu  Thu Oct 13 21:56:31 2022
From: carsen at stanford.edu (Carsen Kline)
Date: Fri, 14 Oct 2022 01:56:31 +0000
Subject: [labnetwork] Cambridge Fiji ALD problems
In-Reply-To: <CAPx0RS-v8jZqecE-4eZ78mu4Mmm-ojZvvQtEfmpaVpRgQW65sg@mail.gmail.com>
References: <CAPx0RS-v8jZqecE-4eZ78mu4Mmm-ojZvvQtEfmpaVpRgQW65sg@mail.gmail.com>
Message-ID: <BYAPR02MB4758A06391B5F5796C644301BF249@BYAPR02MB4758.namprd02.prod.outlook.com>

Eric:

The bulk of the config is stored in a file called setup.ini, located in the Cambridge Nanotech folder. One of ours is attached as an example. If you have plasma and turbo, then more configurations are required under Windows Device Manager for the EdgePort COM port assignments.

We've had great support for legacy Cambridge tools from Veeco with many of the original ALD engineers still working there. Reach them at ALDSUPPORT at veeco.com.

Lastly - backup early, backup often!

Good luck,

Carsen, SNF
________________________________
From: labnetwork <labnetwork-bounces at mtl.mit.edu> on behalf of Eric Fluckiger <eric.fluckiger at utah.edu>
Sent: Thursday, October 13, 2022 10:57 AM
To: labnetwork at mtl.mit.edu <labnetwork at mtl.mit.edu>
Subject: [labnetwork] Cambridge Fiji ALD problems

Dear colleagues,

I have a Cambridge Fiji F200 ALD that has traditionally had driver issues when turning on the encoder and making the handshake with the Windows PC. These driver errors have gone so far as to corrupt the hard drive on the computer, but, I have always been able to reinstall Windows from the BIOS and get the tool to communicate with the PC.

Just recently, some routine maintenance was performed and the tool was shut down from the power source (breakers were turned off). Now, after repowering the tool (following the startup procedure from the manual), the computer does not have any of the configuration settings (MFC, heater, and valve locations along with upper and lower limits). Even though the tool makes the USB connection to the PC when the image of the reactor tries to load, it disappears and is replaced with what I can only assume is the default image with no configuration (see attached image). Also, when I go to load a recipe, it tells me that my recipe parameters are outside of the upper/lower limits of 0/0.

After reading the manual, I noticed that my software is missing the "service" tab that allows you to make the configuration and push it to the tool.

My question: is the configuration for the reactor/MFCs/heaters stored on the Windows PC that interfaces with the tool, or, is that information stored on the E-box inside the tool? I have tried reinstalling Windows several times as well using a different computer and each time the reactor tries to load the configuration and fails.

Follow-up question: I have reached out to Veeco for technical support through their support webpage and have not received a response. Does anyone have any contacts or ALD SMEs that would be able to help me get my ALD back online?

I would be grateful for any insights or help with regard to this matter.

Yours truly,
Eric Fluckiger
Process Engineer
Utah Nanofab


A picture of what my computer is showing after a successful USB handshake. Note: the service tab is missing on my software.

[IMG_3113 (1).jpg]


The missing system configuration tab. This picture was taken from Fiji Manual<https://is.muni.cz/el/1431/jaro2017/F4280/um/69248846/69248852/FIJI_F200_ALD.pdf>. This is what leads me to believe that the configuration settings are stored on the tool itself (E-box).

[Capture.JPG]

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221014/bb24cf79/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: IMG_3113 (1).jpg
Type: image/jpeg
Size: 343196 bytes
Desc: IMG_3113 (1).jpg
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221014/bb24cf79/attachment.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Capture.JPG
Type: image/jpeg
Size: 116101 bytes
Desc: Capture.JPG
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221014/bb24cf79/attachment.jpe>
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: Setup.ini.txt
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221014/bb24cf79/attachment.txt>

From arafat877 at gmail.com  Fri Oct 14 06:26:59 2022
From: arafat877 at gmail.com (Arafat BOUCHAFRA)
Date: Fri, 14 Oct 2022 11:26:59 +0100
Subject: [labnetwork] Microfabrication class
In-Reply-To: <459f3b64-7f8f-7f93-c131-90988b078ccc@uc.cl>
References: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
 <459f3b64-7f8f-7f93-c131-90988b078ccc@uc.cl>
Message-ID: <CAC+p3U7YMsgcbKQEusP9YQwGfBC1cg5oYp61mRHMa6ud5SSGrg@mail.gmail.com>

Hi,

I see that no one has shared any documents that will help in the
microfabrication or microfluidic.

Please share what you have with us, syllabus, Hands-On, courses, PDF...

Regards

Le ven. 14 oct. 2022 ? 03:55, Dr. Lo?k Gence <logence at uc.cl> a ?crit :

> Dear Sergi,
>
> I started a few years ago microfabrication Classes for engineers and
> experimental physicists, here at UC. our cleanroom is small, with CMOS or
> III-V standard processes. Thus we have more flexibility about materials and
> processes.   We did microfluidics devices pump (with ITO electrodes),
> graphene transistors (using comercial monolayer), and basic MEMS with Si
> anisotropic etching, and simple micro-electrodes. Most of the time, the
> devices are not working very well, but It allows the students to go through
> mask design, spin-coating, (use of tweezers!), photolithography, thin-film
> deposition, wet etching, and electrical characterization. I think the
> graphene-based devices are quite simple to fabricate and and always include
> an important electrical characterization part. Microfluidics devices are
> fantastic for students if they have the possibility to characterize under
> microscope the channels with micro-particles for instance...
>
> Hope it helps!
>
>
> Best,
>
> Lo?k
>
>
>
>
>
> Le 07/10/2022 ? 14:39, Sergi Lendinez a ?crit :
>
> Dear labnetwork community,
>
>
>
> Here at LSU we are planning to start a microfabrication class soon, and I
> would like to ask for your opinions about setting up this kind of class at
> a university. I am not sure if this topic has been discussed here before,
> so I apologize for any possible duplication.
>
>
> Any information would be very helpful, like do's and don't's, devices
> being fabricated, number of students, students/teacher ratio, course load,
> etc.
>
>
> I'd like to fabricate some CMOS device, but we lack some critical
> equipment such as a diffusion tube furnace, cvd, or packaging tools, so I'm
> looking for alternate ideas: maybe a photodiode/detector, a Hall sensor or
> some micro-fluidic channels. If anyone has some experience fabricating
> these devices in a class setup, is there anything you'd be willing to share?
>
>
> Many thanks,
>
> Sergi
>
>
>
> *---*
>
> *Sergi Lendinez, Ph. D.*
> Assistant Director NFF | Louisiana State University
>
> Center for Advanced Microstructures and Devices (CAMD)
>
> 6980 Hefferson Highway, Baton Rouge, LA 70803
> (225) 578-9378
>
> sergilendi at lsu.edu | *lsu.edu/nanofabrication*
> <https://lsu.edu/nanofabrication>
>
>
>
> _______________________________________________
> labnetwork mailing listlabnetwork at mtl.mit.eduhttps://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>
> --
> Dr. Lo?k Gence
> Assistant Professor
> Functional Materials & Devices Lab
> Pontificia Universidad Cat?lica de Chile
> Avda. Vicu?a Mackenna 4860,
> CP 7820436 Santiago
> Lab: +56 95504 9648www.lgdeviceslab.com
>
>
> No sienta la obligaci?n de contestar este mail fuera de horario laboral.
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221014/ab1194f9/attachment.html>

From michael.martin at louisville.edu  Fri Oct 14 10:31:00 2022
From: michael.martin at louisville.edu (Martin, Michael)
Date: Fri, 14 Oct 2022 14:31:00 +0000
Subject: [labnetwork] Microfabrication class
In-Reply-To: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
References: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
Message-ID: <BN9PR03MB617075935CBD7ADE10241F6AF2249@BN9PR03MB6170.namprd03.prod.outlook.com>

Hi Sergi,
    We regularly offer a MEMS class and lab at the U. of Louisville.  In years past the lab class has built pressure sensors but this year we are doing "pop-up" structures similar to the microelectromechanical (MEMS) gripper from the Harnett lab found here: https://harnettlab.org/  You can also see some video and photos of the students' progress this term on our Instagram page https://www.instagram.com/micronanolouisville/  And you can find class related resources on our website: https://louisville.edu/micronano/ECE%20544 .
   The students are first walked through the rather straightforward fab sequence to gain familiarity with the cleanroom tools and then they design their own structures followed by doing a second round of fabrication. Another thing we did differently this year is to have the cleanroom staff act as the TA's.  While it is time consuming and bit of a pain (opinions my own) I think the students have had a MUCH better experience than in years past.  Having inexperienced, sometimes apathetic grad students as TA's is not optimal for the undergrads.  That said we doubt we will be doing this again. ?
ECE 544 ? Micro/Nano Technology Center - University of Louisville<https://louisville.edu/micronano/ECE%20544>
ECE 544 Microfabrication/MEMS Laboratory Fall 2022. Home; Expand About Us Submenu About Us. Administration and Staff; Annual Reports; About Us About Us Dropdown Toggle. Administration and Staff
louisville.edu

Harnett Lab - At the University of Louisville J. B. Speed School of Engineering<https://harnettlab.org/>
We used shape-memory alloy (SMA) wire sewn into some denim and stiff plastic using tailored wire placement to form a ?crease? when energized which creates a flexure hinge, allowing the structure to bend. Since we are able to electronically control where this crease is formed we can create a hinge up and down the structure, meaning we can reconfigure the location of the joint.
harnettlab.org
Hope this helps.
Regards,
   Michael
________________________________
From: labnetwork <labnetwork-bounces at mtl.mit.edu> on behalf of Sergi Lendinez <sergilendi at lsu.edu>
Sent: Friday, October 7, 2022 1:39 PM
To: labnetwork at mtl.mit.edu <labnetwork at mtl.mit.edu>
Subject: [labnetwork] Microfabrication class

You don't often get email from sergilendi at lsu.edu. Learn why this is important<https://aka.ms/LearnAboutSenderIdentification>

CAUTION: This email originated from outside of our organization. Do not click links, open attachments, or respond unless you recognize the sender's email address and know the contents are safe.

Dear labnetwork community,



Here at LSU we are planning to start a microfabrication class soon, and I would like to ask for your opinions about setting up this kind of class at a university. I am not sure if this topic has been discussed here before, so I apologize for any possible duplication.


Any information would be very helpful, like do's and don't's, devices being fabricated, number of students, students/teacher ratio, course load, etc.


I'd like to fabricate some CMOS device, but we lack some critical equipment such as a diffusion tube furnace, cvd, or packaging tools, so I'm looking for alternate ideas: maybe a photodiode/detector, a Hall sensor or some micro-fluidic channels. If anyone has some experience fabricating these devices in a class setup, is there anything you'd be willing to share?


Many thanks,

Sergi



---

Sergi Lendinez, Ph. D.
Assistant Director NFF | Louisiana State University

Center for Advanced Microstructures and Devices (CAMD)

6980 Hefferson Highway, Baton Rouge, LA 70803
(225) 578-9378

sergilendi at lsu.edu<mailto:sergilendi at lsu.edu> | lsu.edu/nanofabrication<https://nam11.safelinks.protection.outlook.com/?url=https%3A%2F%2Flsu.edu%2Fnanofabrication&data=05%7C01%7Cmichael.martin%40louisville.EDU%7C1b6302f582564bff34c308daa89b6672%7Cdd246e4a54344e158ae391ad9797b209%7C0%7C0%7C638007682661893366%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&sdata=6Sh85DWjUBaNMMpiQgMK1dZB4slu%2FRTIhXUaE0h1clI%3D&reserved=0>


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221014/21a43e48/attachment.html>

From codreanu at udel.edu  Fri Oct 14 10:57:49 2022
From: codreanu at udel.edu (Iulian Codreanu)
Date: Fri, 14 Oct 2022 10:57:49 -0400
Subject: [labnetwork] Process Engineer position with UN Nanofab
Message-ID: <20269f8a-90dc-d4ac-e619-13d4066e1b30@udel.edu>

Dear Lab Network,

We are looking for a Process Engineer whose main responsibilities are to 
provide user training and support on deposition and dry etch tools. All 
the tools are six years old or newer.

We are located in an area with a relatively low cost of living (e.g. no 
sales tax and low property taxes) and close to major cities in the 
Northeast as well as the beach and the mountains. In addition to 
competitive salaries, UD offers a generous benefit package; some 
highlights are listed below:
-11% University contribution to the retirement plan
-Tuition-free undergraduate education for employees and family members
-Paid time off: 5 weeks of vacation to start with (6 weeks after 5 years 
and 7 weeks after 10 years), 7 holidays/year, and December holiday break
-Health insurance plans with modest premiums and excellent coverage:
http://www.udel.edu/faculty-staff/human-resources/benefits/

The link to the position (Job 499447) is below:
https://careers.udel.edu/cw/en-us/job/499447/process-engineer-ud-nanofabrication-facility

Could you please forward to anyone who may be interested? I would be 
happy to answer questions about the position.

Thank you very much,

Iulian

-- 
iulian Codreanu, Ph.D.
Director, Nanofabrication Facility
University of Delaware
Harker ISE Lab, Room 163
221 Academy Street
Newark, DE 19716
302-831-2784
http://udnf.udel.edu
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221014/c23f7f20/attachment.html>

From repemc at rit.edu  Fri Oct 14 11:51:22 2022
From: repemc at rit.edu (Robert Pearson)
Date: Fri, 14 Oct 2022 15:51:22 +0000
Subject: [labnetwork] Microfabrication class
In-Reply-To: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
References: <CH0P221MB0283505CFDA0C653B3FE68D0CA5F9@CH0P221MB0283.NAMP221.PROD.OUTLOOK.COM>
Message-ID: <SJ0PR16MB475231D93FE005811ABE39CEC3249@SJ0PR16MB4752.namprd16.prod.outlook.com>

Hello Sergi,

My colleagues and I have been teaching a micro-fabrication class here at Rochester Institute of Technology, Microelectronic Engineering since 1982.
We have sophomores, seniors and beginning graduate students all take the class. The class and lab is taught by faculty (with faculty and TA's together in the lab)

Here are my thoughts on such a class and a very early reference to our first level course. I also recommend that you attend UGIM 2024 at MIT to hear first- hand what other universities are doing.

Reference (we have many other papers at UGIM about our curriculum):

R. Pearson, R. Turkman, L. Fuller, and S. Ramanan, PMOS Metal Gate Process, Ideal for Undergraduate Integrated Circuit Fabrication Projects, Proceedings of the Seventh Biennial University Government Industry Microelectronics Symposium, Rochester, NY, June 1987.

You need to teach with a meaningful electrical device as the primary focus, namely a transistor since it is the fundamental element of virtually every semiconductor circuit being made these days. It does not matter if it is NMOS, PMOS or CMOS just that it is a MOSFET.
Enhancement mode PMOSFETs can reliably and easily be made on n-type substrates. NMOSFETS tend to end up as depletion mode devices unless you do a specific threshold voltage adjustment (which might be educational but require outside processing). We here at RIT might be able to help you with that with our ion implanter for a small fee.

The metal-gate (aluminum) PMOS process is a simple 4 mask process and can be done in 7-8 weeks leaving time on the front end of the course for design (layout) and the backend for electrical testing.

If you have your own mask masking capability or direct write (Heidelberg laser writer?) each student can manufacture their own design as  part of a multi-student chip. We give each student a 12-pad (100 by 100 micron pads in two rows of 6) probe configuration (800 by 800 micron total area) to design in. The probe pads match our probe cards and greatly speeds up the electrical testing. We have lots of course and lab notes as well as Silvaco simulation input files that we can share.

You must be able to do doping of some sort to create the source and drain regions. We started by using spin on dopant sources for our drain/source areas and resistors. It is simple and safe. Uniformity can be an issue but it teaches good manufacturing lessons. You can also expand into doing other processes such as double diffused (non-isolated) or triple diffused (isolated) bipolar transistors and diodes.  These processes require more mask levels and longer processing time.

We have actually condensed the 4-level PMOS process into a one-week short course. Maybe you should come to Rochester Institute of Technology sometime and run though it with us.

I would be glad to talk to you further about helping you get your course off the ground.

Sincerely,

Rob Pearson, Ph.D.
RIT - Microelectronic Engineering
robert.pearson at rit.edu<mailto:robert.pearson at rit.edu>
Office: (585) 475-2924

From: labnetwork <labnetwork-bounces at mtl.mit.edu> On Behalf Of Sergi Lendinez
Sent: Friday, October 7, 2022 1:39 PM
To: labnetwork at mtl.mit.edu
Subject: [labnetwork] Microfabrication class

Dear labnetwork community,

Here at LSU we are planning to start a microfabrication class soon, and I would like to ask for your opinions about setting up this kind of class at a university. I am not sure if this topic has been discussed here before, so I apologize for any possible duplication.

Any information would be very helpful, like do's and don't's, devices being fabricated, number of students, students/teacher ratio, course load, etc.

I'd like to fabricate some CMOS device, but we lack some critical equipment such as a diffusion tube furnace, cvd, or packaging tools, so I'm looking for alternate ideas: maybe a photodiode/detector, a Hall sensor or some micro-fluidic channels. If anyone has some experience fabricating these devices in a class setup, is there anything you'd be willing to share?

Many thanks,
Sergi

---
Sergi Lendinez, Ph. D.
Assistant Director NFF | Louisiana State University
Center for Advanced Microstructures and Devices (CAMD)
6980 Hefferson Highway, Baton Rouge, LA 70803
(225) 578-9378
sergilendi at lsu.edu<mailto:sergilendi at lsu.edu> | lsu.edu/nanofabrication<https://lsu.edu/nanofabrication>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221014/381f378a/attachment.html>

From aamer.mahmood at mail.wvu.edu  Mon Oct 17 21:37:38 2022
From: aamer.mahmood at mail.wvu.edu (Aamer Mahmood)
Date: Tue, 18 Oct 2022 01:37:38 +0000
Subject: [labnetwork] Job opening: Manager microfabrication cleanrooms,
 West Virginia University
Message-ID: <BYAPR03MB3640E033C3C7CBA9FE75F377CA289@BYAPR03MB3640.namprd03.prod.outlook.com>

Dear colleagues,
There's an immediate opening for a Manager of the WVU microfabrication cleanrooms.
Job details can be found at the link below.

https://wvu.taleo.net/careersection/wvu_research/jobdetail.ftl?job=20927&tz=GMT-04%3A00&tzname=America%2FNew_York

Please help circulate this opening.
Feel free to reach out to me for further details.
Best regards,


--
Aamer Mahmood
Director
Shared Research Facilities
West Virginia University
Morgantown, WV

(304) 293 9418 (work)
https://sharedresearchfacilities.wvu.edu/

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221018/5bb596df/attachment.html>

From gilheart at rice.edu  Wed Oct 19 11:20:54 2022
From: gilheart at rice.edu (Timothy J Gilheart)
Date: Wed, 19 Oct 2022 10:20:54 -0500
Subject: [labnetwork] Rotational ALD for AZO process?
In-Reply-To: <BYAPR03MB3640E033C3C7CBA9FE75F377CA289@BYAPR03MB3640.namprd03.prod.outlook.com>
References: <BYAPR03MB3640E033C3C7CBA9FE75F377CA289@BYAPR03MB3640.namprd03.prod.outlook.com>
Message-ID: <09A2A904-945F-4BE6-9058-7EA062A056B4@rice.edu>

Howdy all,

Does anyone have the ability to support a rotational ALD process for core-shell nanoparticles similar to the one described in this article (but with AZO-ZnO and/or AZO-Al2O3 instead of Fe3O4-ZnO):

https://www.sciencedirect.com/science/article/pii/S1567173916302668

A diagram from the paper of the relevant apparatus is also attached. Our Veeco Savannah tool is not  equipped for this sort of application.

Happy to refer the student here who needs this to anyone who might be able to support this, either within the lab-network community or outside to a commercial service provider. 

Thanks,

-- 
Tim Gilheart, Ph.D.
Research Scientist - Nanofabrication Cleanroom Manager,
Shared Equipment Authority (SEA), Rice University
https://research.rice.edu/sea/rice-nanofabrication-facility <https://research.rice.edu/sea/rice-nanofabrication-facility>
Cell: 832-341-5488 | Office: 713-348-3159 | gilheart at rice.edu

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221019/19eeb4ac/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Rotational ALD.jpg
Type: image/jpeg
Size: 208753 bytes
Desc: not available
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221019/19eeb4ac/attachment.jpg>

From Etienne.Grondin at USherbrooke.ca  Mon Oct 24 08:50:17 2022
From: Etienne.Grondin at USherbrooke.ca (=?iso-8859-1?Q?=C9tienne_Grondin?=)
Date: Mon, 24 Oct 2022 12:50:17 +0000
Subject: [labnetwork] 2 job offers at Sherbrooke Nanofab, Canada
Message-ID: <QB1PR01MB2913AD8025FD550F142C4D31902E9@QB1PR01MB2913.CANPRD01.PROD.OUTLOOK.COM>

Dear LabNetwork,

Our facility has two open positions, the first one being for an Engineer dedicated to epitaxial growth of group IV, III-V and GaN/AlGaN materials:
Professionnelle ou professionnel de recherche pour l'op?ration et le d?veloppement de proc?d? de syst?mes de croissance cristallographique - Emplois - Universit? de Sherbrooke (usherbrooke.ca)<https://www.usherbrooke.ca/emplois/offre/no/05838>

The second one is for an Engineer specializing in plasma etching:
Professionnelle ou professionnel de recherche pour l'op?ration et le d?veloppement de proc?d? de gravure par plasma - Emplois - Universit? de Sherbrooke (usherbrooke.ca)<https://www.usherbrooke.ca/emplois/offre/no/05884>

Your help to find great candidates would be highly appreciated. The documents are in French but anyone that might be interested in one of these positions can contact me directly for translation and discussion.

Many thanks in advance,
Best regards,

Etienne Grondin
Lab Manager - Nanofab
3IT Universit? de Sherbrooke
e.grondin at usherbrooke.ca<mailto:e.grondin at usherbrooke.ca>
(819) 821-8000 poste 61941
[cid:image001.jpg at 01D8E785.778AC780]<https://www.usherbrooke.ca/3it/fr/>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221024/e13b3627/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 11682 bytes
Desc: image001.jpg
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221024/e13b3627/attachment.jpg>

From hosler0 at purdue.edu  Mon Oct 24 10:44:34 2022
From: hosler0 at purdue.edu (Hosler, Richard S)
Date: Mon, 24 Oct 2022 14:44:34 +0000
Subject: [labnetwork] Jipelec RTA MFC Replacement
Message-ID: <CH2PR22MB178193243D99C2EDFA510B9A9C2E9@CH2PR22MB1781.namprd22.prod.outlook.com>

Hello all,

I have a Jipelec Jetfirst RTA with qualiflow AFC50D MFC units which are showing their age. Has anyone had experience replacing these with another model at a minimum of disruption to the software? The upper DB15 supplies the +/-15V and the RJ-11 RS485 daisy chain is used for comms. If anyone has a known working replacement solution I'd love to hear about it.

Thanks,
Rich

Richard Hosler
Research Engineer
Birck Nanotechnology Center | Room 2287C |
Office:  765.494.4712 | Email: richhosler at purdue.edu<mailto:richhosler at purdue.edu>
Wiki:  https://wiki.itap.purdue.edu/display/BNCWiki
iLabs:  https://purdue.ilabsolutions.com/homepage/
______________________________________________________________

[Purdue_University-150_Years_of_Giant_Leaps.png (300?-66)]

www.purdue.edu/giantleaps<http://www.purdue.edu/giantleaps>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221024/785012ee/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.png
Type: image/png
Size: 11196 bytes
Desc: image001.png
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221024/785012ee/attachment.png>

From James_Goodman at uml.edu  Mon Oct 24 12:04:50 2022
From: James_Goodman at uml.edu (Goodman, James R)
Date: Mon, 24 Oct 2022 16:04:50 +0000
Subject: [labnetwork] Jipelec RTA MFC Replacement
Message-ID: <041D1185-8355-496A-98FD-6680641E819B@uml.edu>

Hello Rich,

I had the same issue last year and was not able to find a replacement. I finally ordered direct replacements from ECM USA.

Jay.

[https://static.uml.edu/email/signature-logo.png]
James Goodman
ETIC Clean Room Equipment Mgr
CORE RESEARCH FACILITY
E: James_Goodman at uml.edu<https://www.uml.edu/service/apps/emailsignaturegenerator/James_Goodman at uml.edu>     T: 978-934-3469



From: labnetwork <labnetwork-bounces at mtl.mit.edu> on behalf of "Hosler, Richard S" <hosler0 at purdue.edu>
Date: Monday, October 24, 2022 at 11:35 AM
To: "labnetwork at mtl.mit.edu" <labnetwork at mtl.mit.edu>
Subject: [labnetwork] Jipelec RTA MFC Replacement

You don't often get email from hosler0 at purdue.edu. Learn why this is important<https://aka.ms/LearnAboutSenderIdentification>
CAUTION: This email was sent from outside the UMass Lowell network.

Hello all,

I have a Jipelec Jetfirst RTA with qualiflow AFC50D MFC units which are showing their age. Has anyone had experience replacing these with another model at a minimum of disruption to the software? The upper DB15 supplies the +/-15V and the RJ-11 RS485 daisy chain is used for comms. If anyone has a known working replacement solution I?d love to hear about it.

Thanks,
Rich

Richard Hosler
Research Engineer
Birck Nanotechnology Center | Room 2287C |
Office:  765.494.4712 | Email: richhosler at purdue.edu<mailto:richhosler at purdue.edu>
Wiki:  https://wiki.itap.purdue.edu/display/BNCWiki<https://nam10.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwiki.itap.purdue.edu%2Fdisplay%2FBNCWiki&data=05%7C01%7Cjames_goodman%40uml.edu%7Cf463d216fae440f2f95e08dab5d538a4%7C4c25b8a617f746f983f054734ab81fb1%7C0%7C0%7C638022225227607576%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&sdata=12mggIIxkzTKH%2BfaJR7q7jgM2SXeyGFA2ClXcgefGwM%3D&reserved=0>
iLabs:  https://purdue.ilabsolutions.com/homepage/<https://nam10.safelinks.protection.outlook.com/?url=https%3A%2F%2Fpurdue.ilabsolutions.com%2Fhomepage%2F&data=05%7C01%7Cjames_goodman%40uml.edu%7Cf463d216fae440f2f95e08dab5d538a4%7C4c25b8a617f746f983f054734ab81fb1%7C0%7C0%7C638022225227607576%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&sdata=Prxuf3GnhDJbj8WXXuFs7hKtcUsNMBxKSbC4OYtt8v8%3D&reserved=0>
______________________________________________________________

[Purdue_University-150_Years_of_Giant_Leaps.png (300??66)]

www.purdue.edu/giantleaps<https://nam10.safelinks.protection.outlook.com/?url=http%3A%2F%2Fwww.purdue.edu%2Fgiantleaps&data=05%7C01%7Cjames_goodman%40uml.edu%7Cf463d216fae440f2f95e08dab5d538a4%7C4c25b8a617f746f983f054734ab81fb1%7C0%7C0%7C638022225227607576%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&sdata=88SIvkmSzELqcbhKkSt%2F%2FeBni%2BEYks4x%2FqOMbhnarF4%3D&reserved=0>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221024/7690e395/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.png
Type: image/png
Size: 11197 bytes
Desc: image001.png
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221024/7690e395/attachment.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image002.png
Type: image/png
Size: 2581 bytes
Desc: image002.png
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221024/7690e395/attachment-0001.png>

From kckeenan at seas.upenn.edu  Tue Oct 25 13:54:26 2022
From: kckeenan at seas.upenn.edu (Kyle Keenan)
Date: Tue, 25 Oct 2022 13:54:26 -0400
Subject: [labnetwork] level of service from ADVACO
Message-ID: <CAGTqYdELpX0FV4Lwr4=ec8QDpGVLeMNmJXAPdH3MKodYe0CC+w@mail.gmail.com>

Hello All,

If any of you on this list use/have used Advanced Vacuum Company (ADVACO)
for your vacuum pump/ cryo pump repairs, I would be very curious to know if
you have experienced any changes in the level of service you have received.
We switched to them years ago because they are very convenient to us, as
they provide pickup/dropoff service. After years of reliable service, we
have experienced a large number of issues with items they have repaired for
us which, prior to 2022, was very unusual. This has caused us a lot of
headaches and resulted in extended tool downtime.

Has anyone else had a similar experience? Have things been just fine for
you? I am very interested in reading what you have to say.

Thank you in advance for your time.

-- 
Kyle Keenan

Laboratory Manager
Quattrone Nanofabrication Facility
University of Pennsylvania
P: 215-898-7560
F: 215-573-4925
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221025/3a8769d2/attachment.html>

From mbradash at purdue.edu  Wed Oct 26 09:39:33 2022
From: mbradash at purdue.edu (Bradash, Mihailo Rayko)
Date: Wed, 26 Oct 2022 13:39:33 +0000
Subject: [labnetwork] Fiji ALD factory reset
Message-ID: <MW5PR22MB3153FCE341300DEE27DF6DADA1309@MW5PR22MB3153.namprd22.prod.outlook.com>

Hello,

I was wondering if anyone who has experience with a Fiji ALD system would happen to know how to factory reset the software, or simply change the Engineering/Admin password?
Our group no longer has access to what the password was originally set at and is needing to make changes to some of the layouts.

Mihailo Bradash
Research Engineer
Purdue University
Birck Nanotechnology Center
1205 W. State Street
West Lafayette, Indiana 47907
Office: (765)494-6522
Cell: (219)670-4974
mbradash at purdue.edu<mailto:mbradash at purdue.edu>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221026/d30a859d/attachment.html>

From sguo18 at yorku.ca  Wed Oct 26 12:27:06 2022
From: sguo18 at yorku.ca (Xin (Shane) Guo)
Date: Wed, 26 Oct 2022 16:27:06 +0000
Subject: [labnetwork] KLA Tencor Alphastep D600 maintenance
Message-ID: <YT2PR01MB42249933EE5C8EC73F78C198AB309@YT2PR01MB4224.CANPRD01.PROD.OUTLOOK.COM>

Hello,

Does anyone know a 3rd party service that can provide maintenance for KLA Tencor Alphastep D600 styplus profilometer in Canada? We have an issue of moving the stage.

Thank you,
Shane Guo
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221026/20777064/attachment.html>

From jtmitch5 at ncsu.edu  Wed Oct 26 12:39:44 2022
From: jtmitch5 at ncsu.edu (James Mitchell)
Date: Wed, 26 Oct 2022 12:39:44 -0400
Subject: [labnetwork] Fiji ALD factory reset
In-Reply-To: <MW5PR22MB3153FCE341300DEE27DF6DADA1309@MW5PR22MB3153.namprd22.prod.outlook.com>
References: <MW5PR22MB3153FCE341300DEE27DF6DADA1309@MW5PR22MB3153.namprd22.prod.outlook.com>
Message-ID: <CAEXS_M94-_nSdQZixwxAy1MRHBNbpJqJnC3GCetsMaF_Og2DdQ@mail.gmail.com>

I will look at ours to see if there is a default password. You could call
Veeco and ask.

Jim

On Wed, Oct 26, 2022 at 11:56 AM Bradash, Mihailo Rayko <mbradash at purdue.edu>
wrote:

> Hello,
>
>
>
> I was wondering if anyone who has experience with a Fiji ALD system would
> happen to know how to factory reset the software, or simply change the
> Engineering/Admin password?
>
> Our group no longer has access to what the password was originally set at
> and is needing to make changes to some of the layouts.
>
>
>
> Mihailo Bradash
>
> Research Engineer
>
> Purdue University
>
> Birck Nanotechnology Center
>
> 1205 W. State Street
>
> West Lafayette, Indiana 47907
>
> Office: (765)494-6522
>
> Cell: (219)670-4974
>
> mbradash at purdue.edu
>
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>


-- 
*Thank you, Jim*

*James Mitchell*
*Specialty Trades Technician*
*Dept. of Electrical and Computer Engineering*
*North Carolina State University Nanofabrication Facility (NNF)*
*MRC RM243A **Box 7911*
*2410 Campus Shore Dr., Raleigh, NC 27606*
*jtmitch5 at ncsu.edu* <jtmitch5 at ncsu.edu>
*Desk: 919-515-5394*
*Cell: 919-717-7325*
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221026/436e9097/attachment.html>

From na2661 at columbia.edu  Thu Oct 27 08:20:56 2022
From: na2661 at columbia.edu (Nava Ariel-Sternberg)
Date: Thu, 27 Oct 2022 08:20:56 -0400
Subject: [labnetwork] KLA Tencor Alphastep D600 maintenance
In-Reply-To: <YT2PR01MB42249933EE5C8EC73F78C198AB309@YT2PR01MB4224.CANPRD01.PROD.OUTLOOK.COM>
References: <YT2PR01MB42249933EE5C8EC73F78C198AB309@YT2PR01MB4224.CANPRD01.PROD.OUTLOOK.COM>
Message-ID: <003a01d8e9fe$9160e100$b422a300$@columbia.edu>

Hi Xin, 

We don't have anyone in Canada but these are 3 party vendors we contacted
from the US about the D600 we used to have. Maybe they can refer you to
someone in Canada.

 

Jeff Cada info at metrologyequipmentservices.com
<mailto:info at metrologyequipmentservices.com> 

 

Or 

 

jefreyhunters at yahuu.com <mailto:jefreyhunters at yahuu.com> 

 

Thanks,

Nava

 

Dr. Nava Ariel-Sternberg

Senior Director of CNI Labs

Columbia University

CEPSR/MC 8903 

530 west 120th st. NY

NY 10027

Office: 212-8549927

Cell: 201-5627600

 

 

From: labnetwork <labnetwork-bounces at mtl.mit.edu> On Behalf Of Xin (Shane)
Guo
Sent: Wednesday, October 26, 2022 12:27 PM
To: labnetwork at mtl.mit.edu
Subject: [labnetwork] KLA Tencor Alphastep D600 maintenance

 

Hello,

 

Does anyone know a 3rd party service that can provide maintenance for KLA
Tencor Alphastep D600 styplus profilometer in Canada? We have an issue of
moving the stage. 

 

Thank you,

Shane Guo

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221027/6d60e801/attachment.html>

From kckeenan at seas.upenn.edu  Thu Oct 27 16:00:48 2022
From: kckeenan at seas.upenn.edu (Kyle Keenan)
Date: Thu, 27 Oct 2022 16:00:48 -0400
Subject: [labnetwork] Zeiss AxioCam ICc5 firewire cameras
Message-ID: <CAGTqYdFaMngdDXkPk4PYGt7i=r8WTDZNcvGNq7a9YC_E+wYQ0g@mail.gmail.com>

Hello All,

I have 3 working Zeiss AxioCam ICc5 *firewire* (*not USB*) cameras that
came from our microscopes after they were upgraded. These cameras are
obsolete/unsupported and are hard to find, thus the reason for our
upgrades. If you have a use for them, they're free to a good home, provided
you arrange the shipping.

Please email me if interested.

Best,
-- 
Kyle Keenan

Laboratory Manager
Quattrone Nanofabrication Facility
University of Pennsylvania
P: 215-898-7560
F: 215-573-4925
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221027/068e334a/attachment.html>

From lino.eugene at uwaterloo.ca  Fri Oct 28 13:12:34 2022
From: lino.eugene at uwaterloo.ca (Lino Eugene)
Date: Fri, 28 Oct 2022 17:12:34 +0000
Subject: [labnetwork] IR and surface acoustic imaging services
Message-ID: <YT2PR01MB4399798ECB19178A2E21ABDF89329@YT2PR01MB4399.CANPRD01.PROD.OUTLOOK.COM>

Dear Labnetwork colleagues,

I am looking for labs or companies that have the capability of doing IR and surface acoustic imaging of bonded wafers.

Best,

Lino Eugene, P.Eng., Ph.D.,
Micro/nanofabrication process engineer
Quantum-Nano Fabrication and Characterization Facility
Office of Research
QNC 1611
University of Waterloo
200 University Avenue West
Waterloo, ON, Canada
N2L 3G1

Ph: +1 519-888-4567 #37788
Cell: +1 226-929-1685
Websites:
https://uwaterloo.ca/quantum-nano-fabrication-and-characterization-facility/
https://fab.qnc.uwaterloo.ca/

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221028/fb64044c/attachment.html>

From Etienne.Grondin at USherbrooke.ca  Mon Oct 31 07:44:40 2022
From: Etienne.Grondin at USherbrooke.ca (=?iso-8859-1?Q?=C9tienne_Grondin?=)
Date: Mon, 31 Oct 2022 11:44:40 +0000
Subject: [labnetwork] IR and surface acoustic imaging services
In-Reply-To: <YT2PR01MB4399798ECB19178A2E21ABDF89329@YT2PR01MB4399.CANPRD01.PROD.OUTLOOK.COM>
References: <YT2PR01MB4399798ECB19178A2E21ABDF89329@YT2PR01MB4399.CANPRD01.PROD.OUTLOOK.COM>
Message-ID: <QB1PR01MB29131371A6FCB4DDA4B338E990379@QB1PR01MB2913.CANPRD01.PROD.OUTLOOK.COM>

Hi Lino,

C2MI Bromont. They operate in industrial mode with a lot of flexibility. Contact me directly if you are interested.

Best regards,

?tienne Grondin
Coordonnateur de laboratoire
3IT Universit? de Sherbrooke
e.grondin at usherbrooke.ca<mailto:e.grondin at usherbrooke.ca>
(819) 821-8000 poste 61941
[cid:image001.jpg at 01D8ECFC.5F276280]<https://www.usherbrooke.ca/3it/fr/>



De : labnetwork <labnetwork-bounces at mtl.mit.edu> De la part de Lino Eugene
Envoy? : 28 octobre 2022 13:13
? : 'labnetwork at mtl.mit.edu' <labnetwork at mtl.mit.edu>
Objet : [labnetwork] IR and surface acoustic imaging services

Dear Labnetwork colleagues,

I am looking for labs or companies that have the capability of doing IR and surface acoustic imaging of bonded wafers.

Best,

Lino Eugene, P.Eng., Ph.D.,
Micro/nanofabrication process engineer
Quantum-Nano Fabrication and Characterization Facility
Office of Research
QNC 1611
University of Waterloo
200 University Avenue West
Waterloo, ON, Canada
N2L 3G1

Ph: +1 519-888-4567 #37788
Cell: +1 226-929-1685
Websites:
https://uwaterloo.ca/quantum-nano-fabrication-and-characterization-facility/<https://can01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fuwaterloo.ca%2Fquantum-nano-fabrication-and-characterization-facility%2F&data=05%7C01%7Ce.grondin%40usherbrooke.ca%7Cf6768350a07a437967e108dab92917f3%7C3a5a8744593545f99423b32c3a5de082%7C0%7C0%7C638025883388853733%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&sdata=87QLj8Wm0pfSCQDcLvZMkg3eMjE0Kk6Vr%2BzKZ6gi9Ts%3D&reserved=0>
https://fab.qnc.uwaterloo.ca/<https://can01.safelinks.protection.outlook.com/?url=https%3A%2F%2Ffab.qnc.uwaterloo.ca%2F&data=05%7C01%7Ce.grondin%40usherbrooke.ca%7Cf6768350a07a437967e108dab92917f3%7C3a5a8744593545f99423b32c3a5de082%7C0%7C0%7C638025883388853733%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C2000%7C%7C%7C&sdata=nSb%2F48pLc%2BZZM5agaionEeYV5BxUlaegCqJ9jalvp9o%3D&reserved=0>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/f8a15374/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 11682 bytes
Desc: image001.jpg
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/f8a15374/attachment.jpg>

From kckeenan at seas.upenn.edu  Mon Oct 31 09:55:59 2022
From: kckeenan at seas.upenn.edu (Kyle Keenan)
Date: Mon, 31 Oct 2022 09:55:59 -0400
Subject: [labnetwork] wet bench manufacturer recommendations
Message-ID: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>

Hello All,

We are in the process of soliciting bids from wet bench vendors for a new
installation project in our lab. Aside from Reynoldstech, I would be
interested in hearing from you about manufacturers who you would be
comfortable recommending.

Thank you for your time.

-- 
Kyle Keenan

Laboratory Manager
Quattrone Nanofabrication Facility
University of Pennsylvania
P: 215-898-7560
F: 215-573-4925
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/0aa44ea1/attachment.html>

From price.798 at osu.edu  Mon Oct 31 11:10:31 2022
From: price.798 at osu.edu (Price, Aimee)
Date: Mon, 31 Oct 2022 15:10:31 +0000
Subject: [labnetwork] Benchtop plating or plating service
Message-ID: <CH0PR01MB71398E2FC38D07DB1078E0D4BC379@CH0PR01MB7139.prod.exchangelabs.com>

Hello labnetwork,
We have a collaborator who needs to plate a few (2-4um) of Au.  We do not maintain a plating setup here at Ohio State.

Does anyone have recommendations for a benchtop plating setup (i.e. not a standalone plating bath/bench)? They have a completely available fume hood that could be used if there was a good option.

Alternatively, does anyone do this as a service?

Thank you,
Aimee Bross Price

Manager, Nanofabrication
The Ohio State University
Nanotech West Lab
Institute for Materials Research
1381 Kinnear Road
Suite 100
Columbus, OH 43212
614-292-2753

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/d1f3c621/attachment.html>

From bgila at ufl.edu  Mon Oct 31 11:48:39 2022
From: bgila at ufl.edu (Gila,Brent P)
Date: Mon, 31 Oct 2022 11:48:39 -0400
Subject: [labnetwork] wet bench manufacturer recommendations
In-Reply-To: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
References: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
Message-ID: <282cd473-0edd-c663-df60-d20ef7ce3568@ufl.edu>

We have benches from JST (https://jstmfg.com/) and Amerimade 
(https://amerimade.com/).? Both products have been great for us.

Best Regards,
Brent
-- 
Brent P. Gila, PhD.
Associate Director, Research Service Centers
University of Florida
1041 Center Drive
Gainesville, Florida 32611
Tel:352-273-2245,? Fax:352-846-2877
email: bgila at ufl.edu

On 10/31/2022 9:55 AM, Kyle Keenan wrote:
> *[External Email]*
>
> Hello All,
>
> We are in the process of soliciting bids from wet bench vendors for a 
> new installation project in our lab. Aside from Reynoldstech, I would 
> be interested in hearing from you about manufacturers who you would be 
> comfortable recommending.
>
> Thank you for your time.
>
> -- 
> Kyle Keenan
>
> Laboratory Manager
> Quattrone Nanofabrication Facility
> University of Pennsylvania
> P: 215-898-7560
> F: 215-573-4925
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/2b0843b2/attachment.html>

From rmorrison at draper.com  Mon Oct 31 12:06:36 2022
From: rmorrison at draper.com (Morrison, Richard H., Jr)
Date: Mon, 31 Oct 2022 16:06:36 +0000
Subject: [labnetwork] wet bench manufacturer recommendations
In-Reply-To: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
References: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
Message-ID: <BN2P110MB1383697E34BC5FF9BB6A629ECE379@BN2P110MB1383.NAMP110.PROD.OUTLOOK.COM>

I would check out ClassOne



Rick





Richard Morrison

PMTS

Draper Laboratory

555 Technology Square

Cambridge Ma  02139

Office: 617-258-3420

Cell: 508-930-3461







From: labnetwork <labnetwork-bounces at mtl.mit.edu> On Behalf Of Kyle Keenan
Sent: Monday, October 31, 2022 9:56 AM
To: Lab Network (labnetwork at mtl.mit.edu) <labnetwork at mtl.mit.edu>
Subject: [labnetwork] wet bench manufacturer recommendations



Hello All,



We are in the process of soliciting bids from wet bench vendors for a new installation project in our lab. Aside from Reynoldstech, I would be interested in hearing from you about manufacturers who you would be comfortable recommending.



Thank you for your time.



--

Kyle Keenan



Laboratory Manager

Quattrone Nanofabrication Facility

University of Pennsylvania

P: 215-898-7560

F: 215-573-4925

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/4d58555b/attachment.html>

From James_Goodman at uml.edu  Mon Oct 31 12:10:26 2022
From: James_Goodman at uml.edu (Goodman, James R)
Date: Mon, 31 Oct 2022 16:10:26 +0000
Subject: [labnetwork] wet bench manufacturer recommendations
In-Reply-To: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
References: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
Message-ID: <370CA3E5-DE75-41C4-AFBE-C63CE888B16B@uml.edu>

Hello Kyle,

We have had very good service from Plastic Concepts in Billerica, MA. Mike Thompson would be your contact.

Jay.

[https://static.uml.edu/email/signature-logo.png]
James Goodman
ETIC Clean Room Equipment Mgr
CORE RESEARCH FACILITY
E: James_Goodman at uml.edu<https://www.uml.edu/service/apps/emailsignaturegenerator/James_Goodman at uml.edu>     T: 978-934-3469



From: labnetwork <labnetwork-bounces at mtl.mit.edu> on behalf of Kyle Keenan <kckeenan at seas.upenn.edu>
Date: Monday, October 31, 2022 at 11:44 AM
To: "labnetwork at mtl.mit.edu" <labnetwork at mtl.mit.edu>
Subject: [labnetwork] wet bench manufacturer recommendations

CAUTION: This email was sent from outside the UMass Lowell network.

Hello All,

We are in the process of soliciting bids from wet bench vendors for a new installation project in our lab. Aside from Reynoldstech, I would be interested in hearing from you about manufacturers who you would be comfortable recommending.

Thank you for your time.

--
Kyle Keenan

Laboratory Manager
Quattrone Nanofabrication Facility
University of Pennsylvania
P: 215-898-7560
F: 215-573-4925
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/04a1154d/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.png
Type: image/png
Size: 2581 bytes
Desc: image001.png
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/04a1154d/attachment.png>

From nidetz at umich.edu  Mon Oct 31 12:10:35 2022
From: nidetz at umich.edu (Robert Nidetz)
Date: Mon, 31 Oct 2022 12:10:35 -0400
Subject: [labnetwork] Benchtop plating or plating service
In-Reply-To: <CH0PR01MB71398E2FC38D07DB1078E0D4BC379@CH0PR01MB7139.prod.exchangelabs.com>
References: <CH0PR01MB71398E2FC38D07DB1078E0D4BC379@CH0PR01MB7139.prod.exchangelabs.com>
Message-ID: <CAEgPQNxSauGsk+52sM66Tk14O_5gLYKe+hOsgpK_iNk_Cpo00w@mail.gmail.com>

Hi Aimee,

We have a gold plating station here at the LNF and offer remote processing
services. Our Au plating solution is BDT-510.

If your collaborator is interested, please have them reach out to us at
info at lnf.umich.edu.

Please let me know if you have any questions.

Thanks, Rob

On Mon, Oct 31, 2022 at 11:48 AM Price, Aimee <price.798 at osu.edu> wrote:

> Hello labnetwork,
>
> We have a collaborator who needs to plate a few (2-4um) of Au.  We do not
> maintain a plating setup here at Ohio State.
>
>
>
> Does anyone have recommendations for a benchtop plating setup (i.e. not a
> standalone plating bath/bench)? They have a completely available fume hood
> that could be used if there was a good option.
>
>
>
> Alternatively, does anyone do this as a service?
>
>
>
> Thank you,
>
> Aimee Bross Price
>
>
>
> Manager, Nanofabrication
>
> The Ohio State University
>
> Nanotech West Lab
>
> Institute for Materials Research
>
> 1381 Kinnear Road
>
> Suite 100
>
> Columbus, OH 43212
>
> 614-292-2753
>
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>


-- 
Robert Nidetz, PhD (he/him/his)
University of Michigan
LNF User Liaison and Domain Expert
1241 EECS Building
1301 Beal Ave
Ann Arbor, MI 48109
nidetz at umich.edu
734.496.8065
Book an appointment: https://calendly.com/nidetz
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/811894f8/attachment.html>

From schweig at umich.edu  Mon Oct 31 12:22:44 2022
From: schweig at umich.edu (Dennis Schweiger)
Date: Mon, 31 Oct 2022 12:22:44 -0400
Subject: [labnetwork] wet bench manufacturer recommendations
In-Reply-To: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
References: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
Message-ID: <CAKzi2_Pec5Ag9EFE=2+XQoWTEc5AB5nz-s_mVZcxUAFZKVY3Cw@mail.gmail.com>

Kyle,

We have several different bench configurations, both inside and outside of
our cleanroom, along with other hardware that was supplied by JST
Manufacturing (https://jstmfg.com/).  We've had good luck with all of it,
other than some wear and tear from our users.

Dennis

734.647.2055 Ofc

On Mon, Oct 31, 2022 at 11:45 AM Kyle Keenan <kckeenan at seas.upenn.edu>
wrote:

> Hello All,
>
> We are in the process of soliciting bids from wet bench vendors for a new
> installation project in our lab. Aside from Reynoldstech, I would be
> interested in hearing from you about manufacturers who you would be
> comfortable recommending.
>
> Thank you for your time.
>
> --
> Kyle Keenan
>
> Laboratory Manager
> Quattrone Nanofabrication Facility
> University of Pennsylvania
> P: 215-898-7560
> F: 215-573-4925
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/e429b28e/attachment.html>

From fnewman at uw.edu  Mon Oct 31 13:51:05 2022
From: fnewman at uw.edu (Fred Newman)
Date: Mon, 31 Oct 2022 10:51:05 -0700
Subject: [labnetwork] Benchtop plating or plating service
In-Reply-To: <CH0PR01MB71398E2FC38D07DB1078E0D4BC379@CH0PR01MB7139.prod.exchangelabs.com>
References: <CH0PR01MB71398E2FC38D07DB1078E0D4BC379@CH0PR01MB7139.prod.exchangelabs.com>
Message-ID: <CAHwjARPd=ryDpub5_qZG-qMBWaaZTpN2my-Xp+ZVCJM3enbEsQ@mail.gmail.com>

Hello Aimee,

We offer Au electroplating service at WNF.

Best regards,
Fred


--
Fred Newman
Research Engineer
University of Washington
Washington Nanofabrication Facility
4000 Mason Rd, Fluke Hall Room 115
Seattle WA 98195-2143
office 206-616-3534  mobile 505-450-4447
fnewman at uw.edu
https://www.wnf.washington.edu/


On Mon, Oct 31, 2022 at 8:41 AM Price, Aimee <price.798 at osu.edu> wrote:

> Hello labnetwork,
>
> We have a collaborator who needs to plate a few (2-4um) of Au.  We do not
> maintain a plating setup here at Ohio State.
>
>
>
> Does anyone have recommendations for a benchtop plating setup (i.e. not a
> standalone plating bath/bench)? They have a completely available fume hood
> that could be used if there was a good option.
>
>
>
> Alternatively, does anyone do this as a service?
>
>
>
> Thank you,
>
> Aimee Bross Price
>
>
>
> Manager, Nanofabrication
>
> The Ohio State University
>
> Nanotech West Lab
>
> Institute for Materials Research
>
> 1381 Kinnear Road
>
> Suite 100
>
> Columbus, OH 43212
>
> 614-292-2753
>
>
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
>
> https://urldefense.com/v3/__https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork__;!!K-Hz7m0Vt54!lphW0Ed1GUnM1Jnzi8ovWHi6McCGasjgcMkCWMVr9vBVoOF4CGeY3VIJ8JVi1b-unygBNVT-bcGtI3CEsw$
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/a8c2f69d/attachment.html>

From yakimom at sunypoly.edu  Mon Oct 31 13:51:54 2022
From: yakimom at sunypoly.edu (Michael Yakimov)
Date: Mon, 31 Oct 2022 17:51:54 +0000
Subject: [labnetwork] wet bench manufacturer recommendations
In-Reply-To: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
References: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
Message-ID: <BY3PR05MB826012ABB22495D316D47506CE379@BY3PR05MB8260.namprd05.prod.outlook.com>

We?re getting one from Burts, hopefully:
https://burtprocess.com/systems/bpe-engineered-systems/wet-benches-and-lab-sinks
Few people around  have a  positive opinion of them

Thanks

mike

From: labnetwork <labnetwork-bounces at mtl.mit.edu> On Behalf Of Kyle Keenan
Sent: Monday, October 31, 2022 09:56
To: Lab Network (labnetwork at mtl.mit.edu) <labnetwork at mtl.mit.edu>
Subject: [labnetwork] wet bench manufacturer recommendations

Hello All,

We are in the process of soliciting bids from wet bench vendors for a new installation project in our lab. Aside from Reynoldstech, I would be interested in hearing from you about manufacturers who you would be comfortable recommending.

Thank you for your time.

--
Kyle Keenan

Laboratory Manager
Quattrone Nanofabrication Facility
University of Pennsylvania
P: 215-898-7560
F: 215-573-4925
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/ffe4a292/attachment.html>

From michael.martin at louisville.edu  Mon Oct 31 14:36:10 2022
From: michael.martin at louisville.edu (Martin, Michael)
Date: Mon, 31 Oct 2022 18:36:10 +0000
Subject: [labnetwork] wet bench manufacturer recommendations
In-Reply-To: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
References: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
Message-ID: <BN9PR03MB6170A807BD4993CAF0FA2716F2379@BN9PR03MB6170.namprd03.prod.outlook.com>

Hi Kyle,
   Our cleanroom uses JST benches:  https://jstmfg.com/wet-bench/ Very nice functionality but a little hard to work on.  Good support though.

Regards,
   Michael
   U. of Louisville
________________________________
From: labnetwork <labnetwork-bounces at mtl.mit.edu> on behalf of Kyle Keenan <kckeenan at seas.upenn.edu>
Sent: Monday, October 31, 2022 9:55 AM
To: Lab Network (labnetwork at mtl.mit.edu) <labnetwork at mtl.mit.edu>
Subject: [labnetwork] wet bench manufacturer recommendations


CAUTION: This email originated from outside of our organization. Do not click links, open attachments, or respond unless you recognize the sender's email address and know the contents are safe.

Hello All,

We are in the process of soliciting bids from wet bench vendors for a new installation project in our lab. Aside from Reynoldstech, I would be interested in hearing from you about manufacturers who you would be comfortable recommending.

Thank you for your time.

--
Kyle Keenan

Laboratory Manager
Quattrone Nanofabrication Facility
University of Pennsylvania
P: 215-898-7560
F: 215-573-4925
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/cdfd46c1/attachment.html>

From robert.j.macdon at gmail.com  Mon Oct 31 19:55:42 2022
From: robert.j.macdon at gmail.com (Robert MacDonald)
Date: Mon, 31 Oct 2022 19:55:42 -0400
Subject: [labnetwork] wet bench manufacturer recommendations
In-Reply-To: <BN2P110MB1383697E34BC5FF9BB6A629ECE379@BN2P110MB1383.NAMP110.PROD.OUTLOOK.COM>
References: <BN2P110MB1383697E34BC5FF9BB6A629ECE379@BN2P110MB1383.NAMP110.PROD.OUTLOOK.COM>
Message-ID: <1FA79977-6B47-42C2-A19C-FB258627E4ED@gmail.com>

waFab is a possibility. 

Thanks,

Rob 

Sent from my iDidntspellcheckit

> On Oct 31, 2022, at 19:54, Morrison, Richard H., Jr <rmorrison at draper.com> wrote:
> 
> ?
> I would check out ClassOne
>  
> Rick
>  
>  
> Richard Morrison
> PMTS
> Draper Laboratory
> 555 Technology Square
> Cambridge Ma  02139
> Office: 617-258-3420
> Cell: 508-930-3461
>  
>  
>  
> From: labnetwork <labnetwork-bounces at mtl.mit.edu> On Behalf Of Kyle Keenan
> Sent: Monday, October 31, 2022 9:56 AM
> To: Lab Network (labnetwork at mtl.mit.edu) <labnetwork at mtl.mit.edu>
> Subject: [labnetwork] wet bench manufacturer recommendations
>  
> Hello All,
>  
> We are in the process of soliciting bids from wet bench vendors for a new installation project in our lab. Aside from Reynoldstech, I would be interested in hearing from you about manufacturers who you would be comfortable recommending.
>  
> Thank you for your time.
>  
> --
> Kyle Keenan
>  
> Laboratory Manager
> Quattrone Nanofabrication Facility
> University of Pennsylvania
> P: 215-898-7560
> F: 215-573-4925
> _______________________________________________
> labnetwork mailing list
> labnetwork at mtl.mit.edu
> https://mtl.mit.edu/mailman/listinfo.cgi/labnetwork
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221031/9a712eca/attachment.html>

From tony.olsen at utah.edu  Mon Oct 31 21:05:24 2022
From: tony.olsen at utah.edu (Tony L Olsen)
Date: Tue, 1 Nov 2022 01:05:24 +0000
Subject: [labnetwork] wet bench manufacturer recommendations
In-Reply-To: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
References: <CAGTqYdHj3-byksyxUqOtU6jHpD0jM-AhGJPZq-tWZ5qK8LNYMw@mail.gmail.com>
Message-ID: <BYAPR11MB3496AD34BAE58B6CF006B635F1369@BYAPR11MB3496.namprd11.prod.outlook.com>

Kyle

We have wet benches from Bold Plastics (www.boldplastics.com/<http://www.boldplastics.com/>) and Wafab International (https://wafab-international.business.site<https://wafab-international.business.site/>).  Both are good.  I?ve used Bold?s wet benches for 40 years.

tonyO


Tony Olsen
Nanofab Cleanroom Supervisor/Process Engineer
University of Utah
36 S Wasatch Drive, Suite 2500
Salt Lake City, UT  84112
801-587-0651
www.nanofab.utah.edu



From: Kyle Keenan <kckeenan at seas.upenn.edu>
Sent: Monday, October 31, 2022 07:56
To: Lab Network (labnetwork at mtl.mit.edu) <labnetwork at mtl.mit.edu>
Subject: [labnetwork] wet bench manufacturer recommendations

Hello All,

We are in the process of soliciting bids from wet bench vendors for a new installation project in our lab. Aside from Reynoldstech, I would be interested in hearing from you about manufacturers who you would be comfortable recommending.

Thank you for your time.

--
Kyle Keenan

Laboratory Manager
Quattrone Nanofabrication Facility
University of Pennsylvania
P: 215-898-7560
F: 215-573-4925
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mtl.mit.edu/pipermail/labnetwork/attachments/20221101/0dd83a53/attachment.html>